background image

 

 

6

Cleaning & Use Guidance

 

1.  Clean  the  inner  liner,  ice basket,  water reservoir,  ice  shovel  and  evaporator frequently. When  cleaning, 

unplug the unit and remove the ice cubes. Use a diluted solution of water and vinegar to clean the inside 

and  the outside surface.    Do not spray with chemicals or diluted agents such as acids, gasoline or oil. 

Rinse thoroughly before restarting.   

2.  Keep ventilation openings in the appliance enclosure, clear of obstruction. 

3.  If unit has been sitting idle for a period of time, the ADD WATER indicator may be flashing, this is due to air 

bubbles trapped in the piping. If this occurs, press the POWER button and unit will return to normal state. 

4.  To ensure the cleanness of ice, please change water for water reservoir at least once a day. If unit is not to 

be used for a long time, please drain the water out and clean. 

5.  If  the  operation  is  interrupted  due  to  water  shortage  or  interruption  of  power  supply,  there  will  be  a 

3-minute delay before unit will restart. This is to protect the compressor.   

6.  Always use fresh water for ice production either at initial installation or after a long shut-off period. 

 

Troubleshooting

   

1. Please note, if a power failure occurs due to disconnection of the power cord, or the power button has been 

pushed off during an ice making cycle, small ice chips may form and get lodged in the ice shovel causing it 

to jam. If this occurs, turn unit off and disconnect power. Gently push the shovel to the rear and remove the 

ice chip. Restart unit.   

 

2. Ice chip lodged in the ice shovel can also cause the water tray to be uneven or ice shovel unable to push ice 

cubes  into  the  basket.    If  this  is  the  case,  turn  unit  off  and  disconnect  power.  Check  for  ice  chips  and 

remove. Restart unit. 

 

 

PROBLEM 

POSSIBLE CAUSE 

SUGGESTED SOLUTIONS 

The compressor works 

abnormally with a buzzing 

noise 

The voltage is lower than 

recommended 

Stop the ice maker and do not restart until 

the voltage is normal. 

Water shortage indicator is on 

1.There is no water 

2.The pump is full of air 

1.Add water up to the MAX line. 

2.Press POWER button to restart 

Indicator lights are not on 

Blown fuse/ No power 

Replace fuse / Turn power on 

The ice made is too large and 

with pieces sticking together. 

1.water  temperature  is  too 

low 

2.Ice  of  previous  cycles  left 

in the water tray 

1.Select small size 

2.Take out the ice under the standby state 

All indicators twinkle 

simultaneously 

Water  tray  is  blocked by  ice 

cube 

Unplug  power.  Take  out  the  ice  that  is 

blocking the tray, then plug the power and 

press  the  POWER  button,  the  machine 

will restart after 3 minutes. 

Summary of Contents for IM-124S








Reviews: