P.5
NOTE: Before starting to spray, retighten the hose clamps to avoid
contamination of the operator and of the environment.
4.2 INSTALLING AND REMOVING THE
BATTERY PACK FROM THE SPRAYER
WARNING:
Make sure switch is in the off position.
To install battery pack:
Insert battery pack into tool until a "click" is heard. Make sure battery pack
is fully seated and latched into position.
To remove the battery pack:
Depress the battery release button and pull battery pack out of tool.
Pull by the plug rather than pulling by the cord when disconnecting
charger. This will reduce risk of damage to electric plug and cord.
Do not use an extension cord unless it is absolutely necessary. Use of
an improper extension cord could result in risk of fire, electric shock, or
electrocution.
An extension cord must have adequate wire size (AWG or American
Wire Gauge) for safety. The smaller the gauge number of the wire, the
greater the capacity of the cable, that is 16 gauge has more capacity
than 18 gauge. When using more than one extension to make up the
total length, be sure each individual extension cord contains at least the
minimum wire size required.
Do not operate charger with a damaged cord or plug – please have
them replaced immediately.
Do not operate charger if it has received a sharp blow, been dropped, or
damaged in any way. Take it to an authorized service center.
Do not disassemble charger; take it to an authorized service center
when service or repair is required. Incorrect reassembly may result in
risk of electrocution or fire.
Disconnect the charger from the outlet before attempting any cleaning.
This will reduce the risk of electric shock. Removing the battery pack will
not reduce the risk.
NEVER attempt to connect 2 chargers together.
The charger is designed to operate on standard household electrical
power(120 Volts). Do not attempt to use it on any other voltage.
•
•
•
•
•
•
•
•
•
4.3 IMPORTANT SAFETY INSTRUCTIONS
FOR BATTERY CHARGERS
CAUTION:
When the charger is plugged into the power supply under certain
conditions, the charger can be shorted by foreign material. Foreign
materials of a conductive nature such as, but not limited to, steel wool,
aluminum foil, or any build up of metallic particles should be kept away from
charger cavities. Always unplug the charger from the power supply when
there is no battery pack in the cavity. Unplug charger before attempting to
clean.
Shock hazard. Do not allow any liquid to get inside charger.
Do not attempt to charge the battery pack with any chargers other than
the ones included in this manual. The charger and battery pack are
specifically designed to work together.
These chargers are not intended for any uses other than charging
rechargeable batteries. Any other uses may result in risk of fire or
electrocution.
Do not expose charger to rain or snow
•
•
•
•
WARNING:
5. Turn On/Off the sprayer
OFF
ON
To install the battery
Insert the battery into tool until an audible click is heard.
To remove the battery
Apply pressure to the trigger on both sides. Release
the battery by pulling out from tool.
(1)
(1)
(2)
To Turn on the sprayer:
1. Turn on the sprayer using the ON/OFF switch. LED light will illuminate to
indicate that the sprayer is ON.
2. When power switch is on, an audible motor sound will be heard. The
Internal pump will operate continuously, solution will circulate through the
pump and back in the tank (if any).
3. Place the lance with the trigger valve pressed above the base of the
sprayer until the spray jet begins to spray continuously.
4. Direct the spray lance to a safe position and open the trigger valve to
begin spraying.
To turn off the sprayer:
1. Shut off the trigger valve. The Internal pump will operate continuously,
solution will circulate through the pump and back in the tank (if any).
2. Turn off the sprayer using the ON/OFF switch. LED light will turn off to
indicate that the sprayer is OFF.
3. Direct the spraying lance to a safe position and open the trigger valve to
release pressure before storing the sprayer.
