background image

Digital Telephone System 

Setup of Conference Phone with Digital Phone System 

Note:

The DT-104 Digital Telephone System Interface is required for use of the Voice Center

Conference Phone with a digital phone system. 

Follow the steps below to set up the system. Throughout the instructions, the Voice Center Conference
Phone is referred to as “Conference Phone” and the DT-104 Digital Telephone System Interface is
referred to as “Digital Interface.”

1. Connect Conference Phone to Digital Interface

using the RJ-45

conference phone cable supplied with the Conference Phone.

• Plug one end of the RJ-45 conference phone cable (larger than a

standard RJ-22 cable) into the connector labeled “Control Box”
on the underside of the Conference Phone.

• Plug the other end of the RJ-45 cable into the Digital Interface

connector labeled “Conference Phone.”

2. Connect Digital Interface to digital telephone

using RJ-22 telephone handset cables.

• Unplug handset “curly cord” from digital telephone and plug it into 

the Digital Interface connector labeled “Handset.”

• Plug one end of RJ-22 telephone handset cable supplied with the Digital

Interface into the Digital Interface connector labeled “Phone.”

• Plug the other end of that RJ-22 cable into the handset jack on the

digital telephone (from which the handset curly cord was disconnected).
See diagram at top of page 9.
Hang up the handset on the digital telephone.

3. Connect Conference Phone power adapter

to Digital Interface.

In North America, use 120 VAC power adapter (PA-102, supplied
with Conference Phone); in Europe, use 230 VAC power adapter 
(PA-202, available in EK-102 international adapter kit).

• Plug DC plug on power adapter cord into the Digital Interface con-

nect labeled “DC15V.”

• Plug power adapter into a nearby electrical outlet (do not exceed 

voltage rating of power adapter).

Note:

At this point, the Conference Phone will emit a musical jingle; 

this self-test allows it to automatically calibrate its performance for 
the acoustic environment. 

Note:

See system illustration on next page.

PHONE

CONFERENCE

PHONE

DC 15V

LINE

PHONE

CONFERENCE

PHONE

DC 15V

LINE

8

PHONE

CONFERENCE

PHONE

DC 15V

LINE

PHONE

CONFERENCE

PHONE

DC 15V

LINE

Summary of Contents for Voice Center CP-2012




















Reviews: