SportsPlay 301-146 10' MGR Installation Instructions Manual Download Page 1

  
 

October 4, 2010  

 

 

301-146 10’ MGR 

INSTALLATION INSTRUCTION 

 

 

INSTALLATION DETAILS 

!

 

Recommended crew (Adult)

: 2-3

 

!

 

Installation time

: 8-12 Hours not including 

concrete cure time

 

!

 

User age

: 5-12

 

!

 

Use zone

: 22’ Diameter 

!

 

Weight

: 990 

!

 

Actual Dimension

: 120” Diameter 

 

WARNING

 

 Use of safety surfacing (wood mulch) in 

compliance with ASTM specification 

F1292 is required.  

MAINTENANCE: 

!

 

As the owner of the playground you are 
responsible for maintenance of the equipment and 
play area.  A maintenance schedule must be 
developed and the equipment inspected frequently.  
Periodic Inspections, maintenance, repair and 
replacement of damaged parts is necessary for the 
safe operation and use of the equipment  

!

 

A maintenance section that includes component 
specific maintenance requirements is included at 
the end of this document. 

 

UNIT IS DESIGNED FOR 12” OF LOOSE RESILIENT 
SURFACING.  WOOD MULCH IS THE MANUFACTURERS 
PREFERED MATERIAL. 
THIS UNIT WILL NOT INSTALL ON POUR IN PLAY.  UNIT 
WILL ALSO NOT INSTALL OVER ANY OTHER 
SURFACING THAT IS LESS THAN 12” HIGH 

 

Summary of Contents for 301-146 10' MGR











Reviews: