Spokey TIDAL, User Manual

Page: 9 / 44

8
www.spokey.eu
www.spokey.pl
Height adjustment of the bike saddle (drawing
– p.42)
Bike saddle height can be adjusted by removing the handwheel and setting
the saddle shank at the correct height.
The shank of the bike saddle has a few holes, i.e. a few possible ways to
get the right seat height.

To adjust the saddle height, loosen the bolt clamping the seat shank in
a bike frame.

Then select the appropriate seat height for a user by moving the saddle
shank up or down.

After selecting a given height, tighten the handwheel so that it is not
possible to change the position of the saddle shank.
Note: Do not remove the seat shank above the minimum or maximum signs
marked on the shaft of the bike saddle.
.
Resistance adjustment
The Resistance adjustment function allows to change resistance on the
pedals. High resistance requires larger effort while pedalling, whereas the
low one decreases the effort. Force of resistance is regulated by a knob
placed on the handlebar post. In order to decrease resistance, adjustment
knob should be turned towards the “1“ number whereas so as to increase
resistance, the knob should be turned towards the “8” number.
In order to achieve a satisfying effect, resistance level should be set during
a training.
MAINTENANCE

Prior to each use of the bicycle, make sure that all the bolts, nuts and
knobs are tightly fitting.

Aggressive cleaning products must not be used to clean the device. Use
a soft, damp cloth to remove dirt and dust. Clean sweat traces since
acidic pH may damage the upholstery.

The device should be kept in a dry place in order to protect it against
dampness and corrosion.

Should the computer work incorrectly, make sure that all the cables are
connected appropriately, especially the upper cable with the computer. If
the computer still does not work, make sure that batteries have been put
in appropriately and that they are not worn-out. If the readout on the
display screen is not legible or some elements are invisible, replace
batteries immediately.

In case of no resistance adjustment, make sure that the upper sensor
cable is well connected with the lower cable.
CAUTION: Due to the protection of the natural environment, worn-out
batteries, power adapters, motors etc. should not be disposed with
household wastes. Worn-out batteries, power adapters, motors etc. should
be taken to a point that will utilise them in agreement with the enforceable
law on environmental protection. It is recommended to check the power
cord and the plug periodically. Never pull the cord. In case of damage, the
device should not be used. Never repair the device on your own. Repairs
s
hould be made by a qualified SPOKEY’s company employee.
POWER SUPPLY
Batteries: 1.5V AAA (2 pieces), not supplied with the bicycle
Inserting batteries
1. Insert two batteries at the back of the counter.
2. Make sure that the batteries are correctly positioned.
3. If the display is unreadable or only some segments are visible, remove the batteries and re-insert them.
4. After removing the batteries, all function values will
be reset.
COUNTER
First start-up
Before the first start-up, make sure that all the cables have been connected
correctly and that the batteries have been inserted correctly.
The display will turn on once you press the button or when you start
pedaling.
Auto on-off
After 4 minutes, the meter enters the energy saving mode. All settings and
data are kept until restarting the meter.
In case the screen does not start, disconnect power supply and wait for 15
seconds.
Device error
If an incorrect reading appears on the counter, remove the batteries and reinsert them.
Button
While touching the button, it allows to select the displaying function. Pressing the button over 3 seconds will reset all functional values to zero
except ODO value
Functions
SCAN: Press MODE button, the arrow will appear and
point to the “SCAN”
position. Then the computer will show all the function one by one. Each
display will be hold for 6 seconds.
PULSE: It indicates your pulse rate during the workout. It is just a reference
data. It starts from 40 to 240BPM.
SPEED: It shows your pedaling speed on the machine. It starts from 0.00
to 99.9km/h.
CALORIES : it shows how many calories you have burned. It starts from
0.00 to 999.9kcal.
DISTANCE: It shows how many Kilometer or Miles you have worked on the
machine. It starts from 0.00 to 999.9km.
ODO (TOTAL DISTANCE) : It shows the total distance after installing the
batteries
。
It starts from 0.00 to 999.9km.
TIMER: It shows your exercising duration. It starts from 00:00 to 99:59min.
SCAN MODE
In the SCAN mode, training effects will be alternately displayed on the
screen: time, calories, speed, distance, total distance, and pulse value.
Each parameter will be displayed for 4 seconds. To switch into this mode, press the MODE button until
“SCAN” is shown on
the screen.
HOW TO OPERATE THE BIKE METER
SCAN
SPEED
DISTANCE
TIME
ODOMETER
CALORIES
PULSE