background image

 
P n e u m a t i c

  R o t a r y   H a m m e r   D r i l l  

2   2 4 0 4   0 0 1 0 ,   0 0 3 0 ,   0 0 4 0

 

M a s c h i n e n f a b r i k   G m b H

 

Spitznas Maschinenfabrik GmbH, Fellerstr.4, D-42555 Velbert, Tel: +49(0)2052 605 0, Fax: +49(0)2052 605 29

, www.spitznas.de

 

Translation of the original manual, 
compiled: 25.05.12 

224040010_30_40_BA_en_Version_01 

Page 3 of 13 

 

SAFETY INSTRUCTIONS 

Any power tool can be dangerous. 
Please follow these simple procedures. 
They are for your protection. 
 

 

 
Wear goggles ( chips – risk of injury) 

 

 
Wear gloves (cutting damages by sharp edged work pieces) 

 

 
Wear safety shoes 

 

 
Wear protective clothing 

 

Remove rings, watches, ties etc. that could be torn by the machine. 
Dress properly. Do not wear loose clothing or jewellery, it can be caught in 
moving parts. 

 

Follow the general current and appropriate Accident Prevention and Safety 
Procedures.

 

 

Never work under the influence of alcohol, drugs or stronger medication. 
 

 

Always make sure that you have a safe foothold. 
Maintain a proper footing and balance at all time. Never work with the machine 
while standing on a ladder or leaning against a scaffold. 

 

Secure the working place well. Use clamps or a vice to fix the work piece. This is 
safer than using hands and clears both hands for operating the machine. 
Hold the machine tight during operation. 

 

 

Keep your working area clean and uncluttered. 
 

 

Keep children away and avoid other persons to come into contact with the 
machine. 

 

 

Switch off the machine if it stops - for any reason - to avoid the unexpected 
starting in uncontrolled condition. 
 

Summary of Contents for 2 2404 0010














Reviews: