Spitwater 10-120H Operating And Maintenance Manual Download Page 6

 

 6 

 
 

1.  OBSERVE SAFETY INSTRUCTIONS 

  Make sure you have read and understood the whole instruction 

manual before installing, operating or carrying out any maintenance 
on this unit. 

  Warnings and serial label on the unit provide important directions 

and information on the safe use of the unit. 

  In addition to these operating and safety instructions please make 

sure that all accident prevention regulations applicable in the 
country of use are followed. 

  In addition to these operating and safety instructions any standards relating to the installation and 

operation of high pressure cleaners applicable in your country must be strictly followed. 

  This unit is not intended for use by children. Children must always be supervised when in the 

vicinity and ensure that they DO NOT play with the unit. Further, it is not intended for use by 
persons with reduced physical, sensory or mental capabilities, or lack of experience or 
knowledge. It must only be operated by persons instructed in its use who have been especially 
authorized to do so. 

  DO NOT operate the unit without appropriate personal protective equipment PPE. 

 

2.  ELECTRICAL CONNECTION 

  The voltage, hertz rating and number of phases on the serial label 

must correspond to that of the electrical mains outlet. 

  Only connect the unit to electrical installation made by 

certified 

electrician and comply with IEC 60364-1.

 

  It is recommended that the electrical supply to this unit should 

include either a residual current device that will interrupt the 
supply if the leakage current to earth 

exceeds 30mA for 30 ms

 or 

a device that will prove the earth circuit. 

  Switching on the unit may cause voltage fluctuations. Voltage 

fluctuations should not occur if the impedance of the transfer point 
is less than 0.15Ω. If in doubt contact your power supplier. 

  This Class 1 Appliance must only be connected to an earthed 

power supply fitted with an appropriately sized fuse. 

 

3.  POWER CORD 

  Make sure before every use that the power cord assembly is not 

damaged or cut. If it is DO NOT connect the unit, have it replaced 
by an electrician or authorized service technician. 

(Type Y 

attachment)

 

  DO NOT pull on the power cord in order to unplug the unit, 

remove the plug from the power outlet.

 

 

 
 
 
 
 
 
 

GENERAL SAFETY PRECAUTIONS 

 

 

 

 

 

 

 

30mA

 

 

 

 

Summary of Contents for 10-120H
























Reviews: