Sphere SSA-850 Installation And Operation Manual Download Page 17 | Manualshive

Page: 17 / 21

Sphere SSA-850 Installation And Operation Manual Download Page 17

Changing Channels

If you have followed the installation and operation instructions, your system should now

be set to the OPTUS C1/D3 satellite and the system should have downloaded the

appropriate channel guides. When the antenna system and satellite receiver is properly

configured, it is easy to change the channel by using the remote control that normally

comes supplied with the Satellite receiver unit. (Please refer to the user manual for your

satellite receiver)

Software Updating

Satellite Frequency/Transponder Data Changed

If some channels work, while one or more other channels do not, or if the antenna
cannot find the selected satellite, the satellite’s frequency data might have changed. You

can visit any authorized Sphere dealer or contact

[email protected]

for further

assistance.

Software updates

Should the transponders change in the future, a software update may be required. You

can visit any authorized Sphere dealer or contact

[email protected]

for further

assistance. New Software will be available at this time. This can be sent via email and is

to be copied to a SD card and inserted into the IDU for a software update.



Copy the new software file to the SD card



Insert the SD card into the SD card port on the IDU



Press the POWER button on the IDU, allow the IDU to copy the new

software file and update the IDU the startup screen will show when the

software is finished updating.



Press the SEARCH button and select the correct zone.

«
...
15
16
17
18
19
...
»

Summary of Contents for SSA-850






















Reviews:

No comments