background image

05

SPEX ARM & THIGH SUPPORT USER MANUAL

10

WWW.SPEXSEATING.COM

Reinstall the top four fasteners, washers and nuts as needed.

Adjust the arm support height as required.

To adjust the thigh support height and position, follow the thigh sup-
port installation guide

Tighten all the fasteners to ensure the position is set. 

6.

5.

7.

8.

9.

Fixed thigh and arm support using M6 x 25mm Fasteners.

Once the user has finished using the Spex Arm & Thigh support, it must be refurbished if it is issued to 
another user. Below are the strict guidelines for refurbishing the Spex Arm & Thigh support. Medifab 
takes no responsibility for contamination, cross infection, or damage.

Reissuing to another user

Part

Procedure

Safety check

All components to be checked for signs of stress or cracking.

Upholstery covers

Upholstery outer covers must be replaced regardless of condition.

Hardware and 
components

Ensure the mechanism components are in place and in safe working order. If 
any are missing, they must be ordered. Check for signs of stress or cracking. 
If any stress/cracks are found the Arm & Thigh support is to be condemned 
and must be disposed of. Clean the hardware and components with a mild 
detergent and quality disinfectant ensuring all areas are free from grime.

Foam

Foam pad must be replaced regardless of condition. 

Summary of Contents for Arm & Thigh Supports

















Reviews: