background image

 

15

Lifetime Limited Warranty

The attention to detail of this fine snap-around instrument is further enhanced by 
the  application  of  A.W.  Sperry s  unmatched  service  and  concern  for  detail  and 
reliability. These A.W. Sperry snap-arounds are internationally accepted by craftsmen 
and servicemen for their unmatched performance. All A.W. Sperry s snap-around 
instruments are unconditionally warranted against defects in material and workmanship 
under normal conditions of use and service; our obligation under this warranty being 
limited to repairing or replacing free of charge, at A.W. Sperry snap-around instrument 
that malfunctions under normal operating conditions at rated use. 

1

Replacement procedure

Securely wrap the instrument and its accessories in a box or mailing bag and ship 
prepaid to the address below. Be sure to include your name and address, as well the 
name of the distributor, with a copy of your invoice from whom the unit was purchased, 
clearly identifying the model number and date of purchase.

A.W.SPERRY INSTRUMENTS INC.

ATT: Customer service dept.

2150

 Joshua s Path, Suite 

302

,

Hauppauge, NY 

11788

1

 

The warranty is not applicable if the instrument has been: misused, abused, subjected 

to  loads  in  excess  of  specifications,  has  had  unauthorized  repair  or  has  been 
improperly assembled or used.

*Note: Recommended calibration interval should not exceed one year. Calibration 
service charges are not covered terms and conditions of warranty.

Summary of Contents for DSA-2417





















Reviews: