Spektrum AR637T Manual Download Page 26

Page: 26 / 27

Compliance Information for the European Union

IC Information

IC: 6157A-TIARLGTNG1
CAN ICES-3 (B)/NMB-3(B)

This device complies with Industry Canada license-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) this device may not

cause interference, and (2) this device must accept any interference, Including

interference that may cause undesired operation of the device.

EU Compliance Statement:

Spektrum AR637T AS3X and SAFE 6 CH Receiver

(SPMAR637T)

;

Hereby, Horizon Hobby, LLC declares that

the device is in compliance with the following: EU Radio Equipment Directive

2014/53/EU; RoHS 2 Directive 2011/65/EU; RoHS 3 Directive - Amending

2011/65/EU Annex II 2015/863.

Wireless Frequency Range and Wireless Output Power:

2402-2478MHz / 19.95dBm
The full text of the EU declaration of conformity is available at the following

internet address: https://www.horizonhobby.com/content/support-render-

compliance.

EU Manufacturer of Record:

Horizon Hobby, LLC

2904 Research Road

Champaign, IL 61822 USA

EU Importer of Record:

Horizon Hobby, GmbH

Hanskampring 9

22885 Barsbüttel Germany

WEEE NOTICE:

This appliance is labeled in accordance with European Directive

2012/19/EU concerning waste of electrical and electronic

equipment (WEEE). This label indicates that this product should

not be disposed of with household waste. It should be deposited

at an appropriate facility to enable recovery and

recycling.

•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Horizon Hobby, LLC

2904 Research Rd.,

Champaign, IL 61822

Email: [email protected]

Web: HorizonHobby.com

Summary of Contents for AR637T




























Search results

Summary of Contents for AR637T

Reviews:

Related manuals for AR637T

Brands by name

Popular brands

Spektrum AR637T, Manual

Search results

Summary of Contents for AR637T

Reviews:

Related manuals for AR637T

Brands by name

Popular brands