Speed Queen KES18AWF Installation Instructions Manual Download Page 6

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

512063

6

Place the dryer in position, and adjust the legs until the 

dryer is level from side to side and front to back. The 

dryer must not rock.

Figure 3 

IMPORTANT: In mobile home installations, gas 
dryers MUST be permanently attached to the floor 
at the time of installation. Order No. 526P3 Dryer 
Installation Kit (available at extra cost) for a 
manufactured (mobile) home installation. Follow 
the instructions supplied with the kit.

Step 2: Connect Dryer Exhaust System

DO NOT use plastic or thin foil ducting. Rigid 

metal duct is recommended.

Locate dryer so exhaust duct is as short as 

possible.

Be certain old ducts are cleaned before installing 

your new dryer.

Use 4 inch (102 mm) diameter rigid or flexible 

metal duct.

The male end of each section of duct must point 

away from the dryer.

Use as few elbows as possible.

Use duct tape or pop-rivets on all duct joints.

Ductwork that runs through unheated areas must 

be insulated to help reduce condensation and lint 

build-up on pipe walls.

DRY2059N

1

Dryer Base

2

Level

3

Leveling Leg

1

2

3

To reduce the risk of fire and combustion 
gas accumulation the dryer MUST be 
exhausted to the outdoors.

W604

To reduce the risk of fire and the 
accumulation of combustion gases, DO NOT 
exhaust dryer air into a window well, gas 
vent, chimney or enclosed, unventilated 
area, such as an attic, wall, ceiling, crawl 
space under a building or concealed space 
of a building.

W045

WARNING

DRY2010N

Figure 4 

This gas appliance contains or produces a 
chemical or chemicals which can cause 
death or serious illness and which are 
known to the State of California to cause 
cancer, birth defects, or other reproductive 
harm. To reduce the risk from substances in 
the fuel or from fuel combustion, make sure 
this appliance is installed, operated, and 
maintained according to the instructions in 
this manual.

W115

To reduce the risk of fire, DO NOT use 
plastic or thin foil ducting to exhaust the 
dryer.

W354

WARNING

DRY2010N

DON’T

DO

Summary of Contents for KES18AWF

















Reviews: