Speed Queen CES68AWF Installation Instructions Manual Download Page 15

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

15

512100

Grounding Information

The dryer must be grounded. In the event of 

malfunction or breakdown, grounding will reduce the 

risk of electric shock by providing a path of least 

resistance for electric current. The dryer is equipped 

with a cord having an equipment-grounding conductor 

and a 3 prong grounding plug. The three-prong 

grounding plug on the power cord should be plugged 

directly into a polarized three-slot effectively 

grounded receptacle rated 110/120 Volts AC 

(alternating current) 15 Amps.

Do not modify the plug provided with the dryer – if it 

will not fit the outlet, have a proper outlet installed by 

a qualified electrician.

NOTE: Have a qualified electrician check the 
polarity of the wall receptacle. If a voltage reading 
is measured other than that illustrated, the 
qualified electrician should correct the problem.

Do not operate other appliances on the same circuit 

when this appliance is operating.

Step 8: Recheck Steps 1-7

Refer to

 Installer Checklist

 on the back cover of this 

manual and make sure that dryer is installed correctly.

Step 9: Check Heat Source

Electric Dryers

Close the loading door and start the dryer in a heat 

setting (refer to the Operating Instructions supplied 

with the dryer). After the dryer has operated for three 

minutes, the exhaust air or exhaust pipe should be 

warm.

This dryer is equipped with a three-prong 
(grounding) plug for your protection against 
shock hazard and should be plugged 
directly into a properly grounded three-
prong receptacle. Do not cut or remove the 
grounding prong from this plug.

W036

WARNING

Improper connection of the equipment-
grounding conductor can result in a risk of 
electric shock. Check with a qualified 
electrician or service person if you are in 
doubt as to whether the dryer is properly 
grounded.

W038

WARNING

To reduce the risk of an electric shock or 
fire, DO NOT use an extension cord or an 
adapter to connect the dryer to the electrical 
power source.

W037

WARNING

DRY2022N

1

“L1”

2

Ground

3

Neutral

4

Neutral Side

5

Round Grounding Prong

Figure 17 

DRY2

0 V.A.C

120±12

V.A.C

Plug cord into separately fused 15 Amp circuit.

3

2

1

4

5

120±12

V.A.C

Summary of Contents for CES68AWF



















Reviews: