background image

 

 

 

 

 

Fig.3 Appearance of the IR-projector Relion-TKV-300-N-IK 

1 - cable glands; 2 - shield; 3 - back cover; 4 - shock-resistant glass; 

5 - earthing bolt; 6 - front panel; 7 - fixing clamps; 8 - hold-down bolt of mounting and positioning 

device; 9 - mounting and positioning device. 

 

4.2

 

FACTORS AFFECTING VISIBILITY  

Such environmental contaminants  as dust, dirt or any  filming agents  reduce illumination  range of  the 

IR- projector as time passes. Routine cleaning of the IR-projector glass is required in the course of operation.  

5.

 

ASSEMBLY OF IR-PROJECTOR  

ATTENTION! 

 

Do not open IR-projectors in the explosion hazardous environment when power supply is on.

 

IR-projector shall be connected in compliance with connection diagram specified in the present Operating 

Manual. If connection diagrams differ from the recommended connection pattern and are not approved by 

the manufacturer, the warranty period shall be terminated and this may result in IR-projector failure. 

Installation and connection of the IR-projector shall be performed by authorized personnel only.

 

5.1

 

INSTALLATION OF IR-PROJECTOR  

IR-projector shall be positioned in  such manner that  to  provide the most  effective illumination  of the 

area subject to CCTV. The following factors shall be taken into consideration:  

 

Installation and targeting of IR-projector shall be performed with due regard to illumination range and 

radiation angle.  

 

IR-projector accessibility provision to perform routine maintenance.  

 

The  IR-projector  shall  be  targeted  descending  on  a  subject  at  minimum  10-20

0

  angle  to  horizon 

(fig.4). Such installation shall prevent moisture accumulation on the projector glass.  

Summary of Contents for Relion-TKV-300-A-IK













Reviews: