manualshive.com logo in svg

Spectris Particle Measuring Systems LiQuilaz II E, Operation Manual

Share
Download
Spectris Particle Measuring Systems LiQuilaz II E Operation Manual Download Page 94

Appendix F Serial Communications Overview

LiQuilaz II E and S Operations Manual

Page F-5

Communication Software Options

Users of Windows XP can use the built-in program HyperTerminal for configuring serial 
communications. Windows 7 no longer includes this program. The following 
alternative utilities available as downloads are discussed:

•

HyperTerminal

, this page

•

PuTTY 

on page

  F-6

•

Tera Term 

on page

  F-7

HyperTerminal

Due to its use in Windows XP (as well as older versions) HyperTerminal remains the 
most ubiquitous program available for serial communications. It is available for 
Windows 7 users as a purchased download from Hilgraeve (

http://

www.hilgraeve.com

) as well as other sites.

Figure F-4  HyperTerminal

 window

Summary of Contents for Particle Measuring Systems LiQuilaz II E














































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands