background image

SpectraPure

®

SpectraPure

®

Inc.

  

480.894.5437   Call us toll-free  1.800.685.2783    

2167 East Fifth St,    Tempe, Arizona   85281

6

The  MaxCap

®

 RODI system comes equipped with two Dual Inline TDS 

monitors. The two TDS meters monitor every step in the purification 
process. The IN probe of the left side meter shows the tap water TDS. The 
OUT probe of the left-side meter shows the RO water TDS. The IN probe 
of the right-side meter shows the TDS coming out of the MaxCap DI and 
the OUT probe of the right-side meter shows the TDS of the final product 
water (out of the SilicaBuster DI).

A pressure - operated Shutoff Valve and a Float Valve are provided for 
convenient filling of a storage reservoir.

A Manual Flush Valve may be used to periodically rinse the accumulated 
impurities and concentrated waste water from the surface of the RO 
membrane to help increase the life of the membrane. If increased pressure 
is needed or desired, use the BPHF-MF-115 Booster Pump Kit. This kit has 
a 24VDC, 2.5A Power Supply.

(continued from previous page)

FLOW RESTRICTORS AND TEST STRIPS:                                             

These  systems are supplied with TWO Flow Restrictors (FR) - RED and 
GREEN. The RED FR (pre-installed) produces a preset waste-to-product 
ratio of 3:1 and the optional GREEN FR has a 2:1 ratio.

Two Test Strips are provided to determine the Total Hardness (this is NOT 
TDS) of your tap water. To test:  Dip the colored end into a small tap water 
sample for 3 seconds. Remove and do not shake. Wait for 20 seconds and 
then match with the closest color block on the back of the package. Color 
is stable for 1 minute.

If the Total Hardness is 180 or greater, you should keep the RED FR installed. 
If the Total Hardness is less than 180, you may replace the RED FR with 
the GREEN FR (see “Working with Push Fittings”). Be sure to note the 
orientation of the removed FR and install the new FR with the same 
orientation. (Refer to Page 9 for location of Flow Restrictor.)

The RED FR has a waste-to-product ratio of 3:1, which will increase the 
amount of water used, but also increase the lifetime of the RO membrane. 
In hard water conditions, you may use the GREEN FR to save water, but 
the RO membrane will not last as long, as it will plug up with hardness 
much more quickly.

Summary of Contents for MaxCap MC-RODI-180-10-MF




























Reviews: