Specter OFF-ROAD 310-73D Installation Instructions Manual Download

Page: 1 / 8

Specter Off-Road Seat Covers are designed and sewn by our own upholstery

professionals on our premises. They are made to industry specifications to be

installed by upholstery professionals and will exhibit a factory original fit. With a little

forethought the average home mechanic will successfully achieve that same original

fit. For a proper fit, we also recommend replacing worn and torn seat foam. Replacement foam can be purchased from

Specter Off-Road. Headrests were a factory option on some 40 series Land Cruisers and are therefore headrest covers

are sold separately, see part numbers below.

Bottom Seat Foam

Headrest Cover

Seat Cover Installation Instructions

1973 - 1984 40 Series Front Bucket Seat Covers

SOR Parts:

310-73D,

310-79D,

310-80D, 310-73D-BD & 310-73D-GD

Specter Off-Road, Inc.

21600 Nordhoff St. Chatsworth, CA 91311 USA,

www.sor.com,

(818)882-1238, Fax: (818) 882-7144

[email protected]

310-73D_0816R3AS

Page 1

#310-81D

SOR High Density

Bottom Molded Foam

Fits 1973-1978 FJ40 & BJ40 front

driver or passenger seat bottom

#310-82D

SOR High Density

Bottom Molded Foam

Fits 1979-1984 FJ40 & BJ40 front

driver or passenger seat bottom

310-73D-AHR SOR Deluxe Vinyl Headrest

Covers-Dark Charcoal Grey

vinyl-Fits 1973-1978

310-79D-H

SOR Deluxe Vinyl Headrest

Covers-Light Charcoal Grey

Fits 1979-8/80

310-80D-H

SOR Deluxe Vinyl Headrest

Covers-Light Charcoal Grey

Fits 8/80-1984

310-73D-GDHR SOR Deluxe Gray Denim

Headrest Covers

Fits 1973-1978 FJ40 & BJ40-

310-73D-BDHR SOR Deluxe Black Denim

Headrest Covers

Fits 1973-1978 FJ40 & BJ40

Summary of Contents for 310-73D









Search results

Summary of Contents for 310-73D

Reviews:

Related manuals for 310-73D

Brands by name

Popular brands

Specter OFF-ROAD 310-73D, Installation Instructions Manual

Search results

Summary of Contents for 310-73D

Reviews:

Related manuals for 310-73D

Brands by name

Popular brands