2
ride if your bicycle shows any of these signs. After any crash, and before you ride any further, take your bicycle to an Authorized Specialized Retailer for a complete inspection.
•
While riding, listen for any creaks, as a creak can be a sign of a problem with one or more components. Periodically examine all surfaces in bright sunlight to check for any small hairline cracks or fatigue at stress points, such as
welds, seams, holes, and points of contact with other parts. If you hear any creaks, see signs of excessive wear, discover any cracks, no matter how small, or any damage to the bicycle, immediately stop riding the bicycle and
have it inspected by your Authorized Specialized Retailer.
•
Lifespan and the type and frequency of maintenance depends on many factors, such as frequency and type of use, rider weight, riding conditions and/or impacts. Exposure to harsh elements, especially salty air
(such as riding near the ocean or in the winter), can result in galvanic corrosion of components such as the crank spindle and bolts, which can accelerate wear and shorten the lifespan. Dirt can also accelerate
wear of surfaces and bearings. The surfaces of the bicycle should be cleaned before each ride. The bicycle should also be maintained regularly by an Authorized Specialized Retailer, which means it should be
cleaned, inspected for signs of corrosion and/or cracks and lubricated. If you notice any signs of corrosion or cracking on the frame or any component, the affected item must be replaced.
•
Regularly clean and lubricate the drivetrain according to the drivetrain manufacturer’s instructions.
•
Do
not
use a high pressure water spray directly on the bearings. Even water from a garden hose can penetrate bearing seals and crank interfaces, which can result in increased bearing and crank wear, which can
affect the normal function of the bearings. Use a clean, damp cloth and bicycle cleaning agents for cleaning.
•
Do
not
expose the bicycle to prolonged direct sunlight or excessive heat, such as inside a car parked in the sun or near a heat source such as a radiator.
WARNING! Failure to follow the instructions in this section may result in damage to the components on your bicycle and will void your warranty, but, most importantly, may result
in serious personal injury or death. If your bicycle exhibits any signs of damage, do not use it and immediately bring it to your Authorized Specialized Retailer for inspection.
WARRANTY
Please refer to the written warranty provisions provided with your bicycle, or visit
www.specialized.com
. A copy is also available at your Authorized Specialized Retailer.
1
2
4
3
13
3 in-lb
f
15
Nm
DROPPER POST
REAR DERAILLEUR
REAR BRAKE
DROPOUTS:
12 x 148mm
GREASE SURFACES
GREASE SURFACES
SEATPOST:
30.9mm
GREASE SURFACES
INSTALL BOTTOM BRACKET SLEEVE
TO PREVENT HOUSINGS FROM
RUBBING ON AXLE
ALL HOUSINGS GO OVER
BOTTOM BRACKET
BOTTOM BRACKET SHELL:
73mm BSA THREADED
FULL LENGTH HOUSINGS
FOR ALL COMPONENTS.
INSTALL FOAM SLEEVES
OVER EACH HOUSING IN
DOWN TUBE
SERVICE PART #
ORACLE DESCRIPTION
1
S192500021
HDS CANE CREEK,CAA2016,41.8/28.6/FLAT IS52/40 W/AL RACE SEAL, CROWN RACE FOR MY20 EPIC/EPIC HT SW
2
S184700003
STC MY18 EPIC SEAT COLLAR 34.9 MM WITH TI BOLT
3
S172600001
HGR MY18 MTB THRU AXLE DER HANGER
4
S170200003
AXL MY17 EPIC HT THRU-AXLE 148MM X 12MM
We may occasionally issue updates and addendums to this document. Please periodically check www.specialized.com or contact Rider Care to
make sure you have the latest information.
Info: [email protected] / 877-808-8154
SPECIALIZED BICYCLE COMPONENTS
15130 Concord Circle, Morgan Hill, CA 95037 (408) 779-6229
0000138914_UM_R1, 04/19
