Page 4
VSL60-IR Owner’s Manual
940 Columbia Ave.,
Riverside CA 92507-4492
(800) 448-0976 Fax (9
51
) 787-8747
www.speakercraft.com
SpeakerCraft
LIT90175
®
LIMITED 5-YEAR WARRANTY
SpeakerCraft Inc. warrants to the original retail purchaser
only
that this SpeakerCraft product will be free from defects in materials and workmanship for a period of five years, provided
the speaker was purchased from a SpeakerCraft Authorized Dealer.
Defective products must be shipped, together with proof of purchase, prepaid insured to the SpeakerCraft Authorized Dealer from whom they were purchased, or to the SpeakerCraft
factory at the address listed on this installation instruction manual. Freight collect shipments will be refused. It is preferable to ship this product in the original shipping container to
lessen the chance of transit damage. In any case, the risk or loss or damage in transit is to be borne by the purchaser. If, upon examination at the Factory or SpeakerCraft Authorized
Dealer, it is determined that the unit was defective in materials or workmanship at any time during this warranty period, SpeakerCraft or the SpeakerCraft Authorized Dealer will, at
its option, repair or replace this product at no additional charge, except as set forth below. If this model is no longer available and cannot be repaired effectively, SpeakerCraft, at its
sole option, may replace the unit with a current model of equal or greater value. In some cases where a new model is substituted, a modification to the mounting surface may be
required. If mounting surface modification is required, SpeakerCraft assumes no responsibility or liability for such modification. All replaced parts and product become the property of
SpeakerCraft Inc. Products replaced or repaired under this warranty will be returned to the original retail purchaser, within a reasonable time, freight prepaid.
This warranty does not include service or parts to repair damage caused by accident, disaster, misuse, abuse, negligence, inadequate packing or shipping procedures, commercial use,
voltage inputs in excess of the rated maximum of the unit, or service, repair or modification of the product which has not been authorized or approved by SpeakerCraft. This warranty also
excludes normal cosmetic deterioration caused by environmental conditions. This warranty will be void if the serial number on the product has been removed, tampered with or defaced.
This warranty is in lieu of all other expressed warranties. If the product is defective in materials or workmanship as warranted above, the purchaser’s sole remedy shall be repair or
replacement as provided above. In no event will SpeakerCraft be liable for any incidental or consequential damages arising out of the use or inability to use the product, even if
SpeakerCraft Inc. or a SpeakerCraft Inc. Authorized Dealer has been advised of the possibility of such damages, or for any claim by any other party. Some
states do not allow the exclusion or limitation of consequential damages, so the above limitation and exclusion may not apply.
All implied warranties on the product are limited to the duration of this expressed warranty. Some states do not allow limitation on the length of an implied
Warranty. If the original retail purchaser resides in such a state, this limitation does not apply.
Should you have any questions regarding this, or any other SpeakerCraft product, please call our toll-free service hotline at
1-800-448-0976. We are available to assist you every weekday, except holidays, between the hours of 7:00 a.m. and 5:00 p.m. PST.
SpeakerCraft offers a variety of accessories to make your installation of this and other SpeakerCraft products easy, economical, and
professional. Contact your authorized SpeakerCraft Dealer for more information.
STATUS Brightness
Diagram 3
also shows how an external resistor can be added to reduce the brightness of the Status LED’s on SpeakerCraft IR
Receivers to any desired level. Note that the VSL60-IR does not support Brightness.
In this example, a PS-1.0 12V DC Power Supply is used as the voltage source to indicate the ON/OFF status of an A/V Receiver.
Choose a resistor value that achieves the brightness you desire (about 2.2k to 12k, 1/8 W). Connect it in series with the STATUS
lead on each IR receiver desired, as shown.
MOUNTING THE VSL60-IR
Once the VSL60-IR has been wired, it is ready to be mounted into the wall. Use the screws provided to hold the components
in place.
IR RECEIVER SPECIFICATIONS
• Exclusive Ambient Noise Suppressor (ANS) system
• Requires Power Supply, Terminator Block, and Emitters
• IR Lens rejects visible light interference
• Crosshatch Shield (internal) inhibits EMI/ESI Interference
•
Power:
12V DC @ 6 mA supplied from connected Terminator
•
Carrier Frequency Acceptance Range:
28 - 90 kHz
•
Control Range:
Up to 35 feet, depending on remote
strength and ambient noise conditions
•
Control Angle:
±50˚ off axis
VOLUME CONTROL SPECIFICATIONS
•
Power Rating:
60 Watts
•
Steps:
12 (make before break)
•
Frequency Response:
20Hz - 20kHz
•
Total Attenuation:
42dB maximum
• Removable Screw Down Terminals
• Includes Decora* Style Insert Plate
• Conventional J-Box mounting with the screws provided
•
Dimensions:
H 4" (102mm) x W 1
5
⁄
8
" (41mm) x D 3
1
⁄
16
" (78mm)
* Decora is a registered trademark of The Leviton Manufacturing Co., Inc.