BassX-Dual 6 Owner’s Manual
Page 3
Page 2
BassX-Dual 6 Owner’s Manual
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufactur-
er’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves or other
apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding-type
plug has two blades and a third grounding prong. The wide blade or third prong
is provided for your safety. If the provided plug does not fit into your outlet, con-
sult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket or table specified by the
manufacturer or sold with the apparatus. When a cart is used, use caution when
moving the cart / apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of
time.
14. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or
has been dropped.
15. The appliance couple of the power supply cord is used as the ultimate disconnect
device from mains. Remain the appliance couple readily operable.
16. Apparatus shall not be exposed to dripping or splashing and objects filled with
liquids shall not be placed on the apparatus.
SpeakerCraft’s BassX Dual 6 Compact Floor Standing Subwoofer provides accurate bass to any audio system, and is designed to work in conjunction with
your other audio components. The BassX Dual 6 can be connected to any surround sound receiver that has a subwoofer output, any receiver that has a
built-in preamplifier or any receiver that has speaker level outputs.
INTRODUCTION
For optimal performance, the BassX Dual 6 should be placed in a corner along the same wall as the front speakers. The unit is not shielded, so do not
place it too close to video devices. When choosing a place for the BassX Dual 6, please keep the following in mind: Placing the BassX Dual 6 in a corner
will increase the bass output. For details on placement, consult your local SpeakerCraft dealer.
DO
• Place the BassX Dual 6 with its feet resting on a solid flat level surface.
• Place the BassX Dual 6 in a well-vented area to provide proper cooling. In areas that lack proper ventilation, such as tight cabinets or racks, it may
be necessary to install small fans to create air movement.
DON’T
• Obstruct the woofers of the BassX Dual 6 it will hinder performance.
• Place the BassX Dual 6 in any position other than horizontal with the feet down. Never place on its side or resting on the back where the terminals are
located.
• Place the BassX Dual 6 near heat sources or in an area that it would be exposed to moisture.
PLACEMENT
CAUTION:
Only make connections when the BassX Dual 6 is turned off.
Connecting the Line Level Audio Inputs (See Figure 1)
If your surround sound receiver or amplifier has only one subwoofer output, simply plug it into the
Left Line Input. If your receiver or amplifier has a built-in preamplifier, the left and right pre-outputs
can be connected to the left and right line level inputs.
Connecting the Line Level Audio Outputs (See Figure 1)
Sources connected to the left and right line level inputs can be forwarded to other components
or amplifers by connecting to the corresponding outputs. If your receiver or amplifier has a built-in
preamplifier, the left and right pre-inputs can be connected to these line level outputs.
INSTALLATION
Once the BassX Dual 6 is connected, use the controls described below to make adjustments so that it
will blend seamlessly with the other speakers in your system.
Power Switch (See Figure 2)
This switch turns the BassX Dual 6 on or off. The Standby light will illuminate green when switched
to the “On” position; when “Off”, the Standby light will illuminate red.
Volume Knob (See Figure 3)
Use this control to match the output of the BassX Dual 6 to that of the main speakers in the system.
We recommend that you play a variety of material before selecting a setting. Start with the control
in the 12 o'clock position for the optimal setting and adjust to your system as necessary.
Crossover Knob (See Figure 3)
Use this control to adjust the upper frequency limit of the BassX Dual 6. The purpose is to control the
overlap the upper frequencies of the sub and the main speakers’ lower frequencies. Start in the 12
o’clock position for the optimal setting.
Phase Switch (See Figure 4)
Allows you to toggle between 0° and 180° phase modes. Listen to the system and leave the switch
in the position that has more audible bass. The default setting is “0˚”.
OPERATION
The BassX Dual 6 Powered Subwoofer is designed to function trouble-free. Most problems occur due to operating errors. If you have a problem, please check
the troubleshooting list first. If the problem persists, contact your authorized SpeakerCraft dealer or SpeakerCraft Technical Support at 800.448.0976.
TROUBLESHOOTING
A hum or buzzing sound is heard.
The sound may be caused by a ground loop in the system. Try to eliminate this
by reversing the AC plugs of other components in the system.
Try plugging the receiver into another outlet.
Other causes may include faulty cables.
The BassX Dual 6 will not turn on.
The subwoofer must be plugged into a live AC outlet. The power switch on
the back panel must be on. A signal must be playing into the input
jacks.
No sound is heard.
Audio cable to the receiver is not connected properly or the cable is bad. Use
another cable that you know is good.
Check all wire connections and plugs.
Problem
Possible Causes & Solutions
Figure 1:
Line Level Inputs/Outputs
APPLICABLE FOR USA, CANADA OR WHERE APPROVED FOR USAGE
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE PLUG TO WIDE
SLOT, INSERT FULLY.
ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAME LA
PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET
POUSSER JUSQU AU FOND.
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: To reduce the risk of electric
shock, do not remove cover (or back).
No user-serviceable parts inside. Refer
servicing to qualified service personnel.
IMPORTANT SAFETY INSTRUCTIONS
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert you to the presence of uninsulated “dan-
gerous voltage” within the product’s enclosure
that may be of sufficient magnitude to consti-
tute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert you to the presence
of important operating and maintenance (ser-
vicing) instructions in the literature accompany-
ing the appliance.
• Explanation of Graphical Symbols
WARNING
RISK OF ELECTRIC SHOCK
DO NOT EXPOSE TO MOISTURE
• To reduce the risk of fire or electrical
shock, do not expose the apparatus to
rain or moisture.
• A warning that an apparatus with CLASS
I construction shall be connected to a
MAINS socket outlet with a protective
earthing connection.
PORTABLE CART
WARNING
CAUTION: Please read the following important instructions carefully to ensure a safe operation.
Figure 2:
Power Switch; Standby Light
Figure 3:
Volume / Crossover Knobs
Optimal Settings Indicated
Figure 4:
Phase Switch
Default Setting Indicated
