G
O P E R AT I N G I N T R U C T I O N S
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent the
technical status at the time of printing.
© Copyright 2015 by Conrad Electronic SE.
Triple Table Mount for LCD Monitor Arm
Item no. 416081
Intended use
The product is used to mount three LCD monitors with “VESA Wallmount System” (75 mm or 100 mm) and
a maximum weight of 8 kg each to a table.
For safety reasons, you may not convert and/or alter the product. If you use the product for purposes other
than those described above, the product may be damaged. Please read the operating instructions carefully
and do not discard them.
If you pass the product on to a third party, please hand over these operating instructions as well.
This product complies with the applicable national and European requirements. All names of companies and
products are the trademarks of the respective owners. All rights reserved.
Package Contents
• see part list in the enclosed original manufacturer’s instructions
• Operating instructions
Safety Instructions
The warranty/guarantee will be void in the event of damage caused by failure to observe
these operating instructions. We do not assume any liability for any resulting damage.
We do not assume any liability for material and personal damage caused by improper use
or non-compliance with the safety instructions. In such cases, the warranty will be null
and void.
The exclamation mark symbol indicates that important information is included in these
operating instructions.
The arrow symbol indicates tips and notes.
Persons/product
• Do not overload the monitor arm. Pay attention to the details provided by the manufacturer for the maxi-
mum weight of the monitors.
• Fasten the monitor arm only at a sufficiently stable table top/table. Tables made of glass, ceramic or stone
slabs or thin plastic-coated wooden-fibre slabs are not suitable for attachment. Furthermore, you must not
attach the monitor arm to shelves or similar unstable or unsteady surfaces. Selecting an unsuitable instal-
lation location can lead to personal or material damage.
• Check the screw connections of the table mount, monitor arm and monitors from time to time. Adjusting
the position of the monitor arm and the monitors and moving them can sometimes cause the screws to
become loose over time.
• Fasten the monitor arm only to a sufficiently stable location. Consider the strong lever action of the monitor
arm.
• Do not exert any force when moving/adjusting the monitor, as this could damage the monitors.
• When moving/adjusting, do not press on the screens of the monitors.
• For safety reasons, the monitor arm with the monitors mounted to the table should always be above the
table top.
• Do not use the monitor arm to support yourself or to pull yourself up.
• Suitable mounting material must be used for wall mounting. Furthermore, the construction of the wall must
be suitable for wall mounting. If you do not have specialist knowledge, contact an expert or specialist
workshop.
• Make certain when mounting the product on a wall that nobody is situated in the area underneath the
monitor arm and the monitors.
• The product is not a toy. Keep out of the reach of children and pets.
• Do not leave packaging material carelessly lying around. It may become a dangerous plaything for chil-
dren.
• Never expose the product to any excessive mechanical stress.
Miscellaneous
• If you have doubts about the operation, safety or installation of the product, consult a trained technician.
• Maintenance, adjustment and repair work may only be carried out by an expert or a specialist workshop.
• If you have any questions,that are not answered in these operating instructions, please contact our techni-
cal customer service or another specialist.
Part list
see part list in the enclosed original manufacturer’s instructions
Version 03/15
Table-mounting
Carry out only the work necessary to install (or adjust) the monitor arm. Never perform
any conversion or repair work.
Apply your full concentration when carrying out the installation, because if the monitors
or monitor arm were to fall, this could cause expensive damage to the equipment and
there is the potential danger of personal injury!
Lay all the cables of the monitors in such a way that they do not get jammed or kinked in
the monitor holder.
Proceed with care when assembling and mounting the product. The product may have
sharp edges. There is a risk of injury!
Detailed images for mounting and positioning of the screws can be found in the original manu-
facturer’s instructions.
You may need a cross-head screwdriver (not included in the delivery) to tighten the cross-head
screws.
To not scratch the table surface during assembly! If necessary, use e.g., a protection mat or
several page of thick newspapers.
The assistance of a second person is required when mounting the monitors to the monitor arm.
This person must hold the monitors while you fasten them to the holders.
Image 1:
• Select two mounting holes depending on the thickness of you table to fasten the screw clamp (B) to the
stand rod (A). Always select a pair of holes at the same height.
• Fasten the screw clamp (B) to the lower part of the stand rod with the hexagonal screws (N). To do this,
use the large hexagonal spanner (H).
• Fasten the screw clamp (B) to the table edge. Make sure that the table is stable and the mounting surface
is even.
Image 2:
• Attach the two cross beams (C) to the cross beam holder (D). Fasten both using two hexagon socket
screws (K) each. Use the small hexagonal spanner (J).
• Unscrew the screw at the side of the monitor holder (E2) and slide out the holder plate.
• Fasten the loose holder plate as shown in the middle of the two cross beams (C) using two cross-head
screws (L). Use an appropriate hexagonal spanner to do this.
Image 3:
• Place the cross beam mounted previously onto the stand rod (A). Please pay attention to the correct align-
ment. The arrow must point upwards and the word “UP” must be visible.
• Adjust the cross beam at the desired height and fasten it to the stand rod (A) with two Allen screws (O). To
do this, use the large Allen wrench (H).
• Place the decorative caps (G) on the stand rod (A).
Image 4:
• Fasten the two monitor holders (E1) to the backsides of the two outer monitors. Use the cross-head screws
(M) and pay attention to the correct alignment. The wing screws must point upwards in both cases.
• Fasten the holder plate (E2) to the backside of the monitor in the middle using the four cross-head screws
(M). Observe the correct alignment (see illustration).
Image 5:
• Slide the monitor in the middle and the holder plate into the monitor holder in the middle of the cross beam.
Secure the holder with the screws on the side.
• Loosen the screws at the end of the cross beam and remove the plastic covers. Slide the outer monitors
onto the cross beam.
• Adjust the correct position and fasten the monitors with the wing screws of the respective monitor holder.
• Re-attach the plastic overs at the ends of the cross beam.
Image 6:
• Pass the connection cables of the monitors through the stand rod (A).
• Fasten the connection cables to the cross beam holder (D) using the cable clamps. Use cable ties (F) to
secure the cables at the cross beam.
Image 7:
• You can tilt the outer monitors to achieve an ideal viewing perspective.
• To adjust the swivel joint, you must remove the decorative caps first.
• Loosen the adjustment screw with the screw driver (I) until the joint can be rotated.
• Set the desired angle and then tighten the set screw firmly.
• Replace the decorative cap.
Technical Data
Suitable display sizes ..................33 - 61 cm (13 - 24“)
Bearing load ................................3 x max. 8 kg
Thickness of table top ..................max. 10 cm
VESA standard ............................75 x 75 mm, 100 x 100 mm
Dimensions (W x H x D) ..............141,8 x 68,2 x 28 cm
Weight .........................................approx. 8.6 kg