6
EN
TK 70
▪ Do not use blades which body is thicker and
teeth set thinner than the slotting knife thick-
ness 2 mm.
▪ Do not dismount the slotting knife, except
when performing a “plunge cut”.
▪ The mobile guard must not be locked in open
position during the intervals between different
operations.
▪ Upon jamming the blade, switch off the ma
-
chine immediately (by releasing the switch
lever).
▪ Support large panels to minimise the risk of
blade jamming and kickback. Large panels
tend to sag under their own weight. Supports
must be placed under the panel on both sides,
near the line of cut and near the edge of the
panel.
▪ Rags, cloths, cord, string and the like should
never be left around the work area.
▪ Always keep the cord away from the working
area of the power tool.
▪ Never use the machine with a damaged ca
-
ble. Do not touch the damaged cable and pull
the mains plug when the cable is damaged
while operating. Damaged cables increase
the risk of electric shock.
▪ Hold the power tool only by the insulated grip
-
ping surfaces when performing an operation
where the cutting tool may contact hidden
wiring or its own cord. Contact with a “live”
wire will also make exposed metal parts of the
power tool “live” and shock the operator.
▪ The tool must be used only for its prescribed
purpose. Any use other than those mentioned
in this Manual will be considered a case of
misuse. The user and not the manufacturer
shall be liable for any damage or injury result-
ing from such cases of misuse.
▪ To use this tool properly, you must observe
the safety regulations, the assembly instruc-
tions and the operating instructions found in
this Manual. All persons who use and service
the machine have to be acquainted with this
Manual and must be informed about its poten-
tial hazards. Children and frail people must not
use this tool. Children should be supervised
at all times if they are in the area in which the
tool is being used. It is also imperative that
you observe the accident prevention regula-
tions in force in your area. The same applies
for general rules of occupational health and
safety.
▪ The manufacturer shall not be liable for any
changes made to the tool nor for any damage
resulting from such changes.
▪ Power tools must not be used outdoors in
rainy weather, or in moist environment (after
rain) or in close vicinity with easily flammable
liquids and gases. The working place should
be well lit.
V - Know your product
Before using the power tool, familiarize your-
self with all the operating features and safety
requirements.
Use the tool and accessories only for the ap-
plications intended. All other applications are
expressly ruled out.
1. ON/OFF switch locking button
2. ON/OFF switch lever
3. Nut for fixing the cutting depth/ruler
4. Parallel guide/ruler
5. Thrust washer
6. Blade tightening screw
7. Parallel guide fixing nut
8. Clamping washer
9. Slotting knife
10. Mobile guard
11. Screw for fixing the slotting knife
12. Allen key
13. Nut for adjusting bevel cutting/ruler
14. Adapter
15. Screw
16. Washer
17. Screw
18. Saw blade
VI - Operation
This power tool is supplied from single-phase al-
ternating current mains only. It is double insulat-
ed according to EN 60745-1 and IEC 60745 and
can be connected to grounded or not grounded
sockets. This power tool is radio suppressed in
compliance with EMC Directive 2004/108/EC.
This power tool is designed for longitudinal and
cross sawing wood in a straight line at bevel an-
gle from 0° to 45°.
PRIOR TO INITIAL OPERATION
▪ Make sure the power supply voltage corre
-
sponds to the value indicated on the name
plate with technical data of the tool.
▪ Always check the position of ON/OFF switch.
The power tool must be connected to the
power supply socket only when this switch is
in OFF position. If the plug is connected to
Та
ше
в
-
Га
лв
ин
г
ОО
Д
www.tashev-galving.com
