background image

 

   

TOOL SELECTION 

The beater, whisk and spiral dough hook are tools for 

the work implied by their names. Do not use the beater 

for dough making or the whisk for anything other than 

whisking, aerating or mixing light mixtures.   

The 

Table 1

 shows the typical uses for each of the 

tools. For more details, please refer to Page 14. 

NOTE: Always wash agitator with mild soap and apply 

light quantity of mineral oil to planetary shaft after cleaning.

 

 

FITTING THE BOWL 

With the bowl cradle lowered, place the chosen mixing tool in the bowl 

and position the bowl on the cradle. There are three location points when 

fitting the bowl. Please refer to 

Figure 2

:   

(1) The locking pin at the rear of the bowl should locate in the hole of the 

cradle.   

(2) The two holes in the bowl handles must engage on the pins located on the 

cradle.   

(3) Please ensure that the bowl is seated correctly on the cradle before 

securing the bowl locking latches prior to use. 

(For Bigger Capacity Mixer, above 50 Liter) 

NOTE: Please use bowl truck to load and unload bowl containing more than 

50lbs per batch. 

FITTING THE MIXING TOOL 

Slide the bayonet fitting of the agitator onto the drive shaft and twist clockwise to 

secure it in position. To remove the agitator, slide the tool up the shaft slightly and twist 

counter clockwise. Please refer to 

Figure 3

NOTE: Install the bowl BEFORE inserting agitators. 

NOTE: Agitators should always rotate in a clockwise direction around bowl. If agitators 

move counterclockwise, please contact licensed electrician immediately to remedy 

incorrect wiring. 

BOWL LIFT & BOWL GUARD 

The bowl cradle and bowl guard are electrically interlocked so that the machine will only operate with 

the bowl cradle at the raised position. In addition to this, the bowl guard must be locked into place by 

sliding it into position across the top of the bowl to the point where it will slide no further.   

NOTE: Only once the bowl is raised and the bowl guard locked, the machine can operate.

 

Thus ensuring 

total user safety at all times. Once the guard has been opened or the bowl lowered, the machine will 

stop immediately. The Mixer can only be restarted by pressing the start button again. 

During the mixing process, additional ingredients can be added by the chute located on the right hand 

side of 

the 

bowl 

guard. 

 

THE REMOVABLE BOWL GUARD   

 

Spiral Dough Hook:

 Heavy mixes 

such as dough, pie pastry. . 

 

Whisk: 

Light mixes such as 

whipped cream, mayonnaise, 

egg whites, pancakes and 

soufflés. 

Operating Instructions 

Table 1 

Figure 2 

 

Figure 3 

Summary of Contents for HI Series


















Reviews: