9
GB
GENERAL INFORMATIONS
2.
WARRANTY
2.1
Check the booth on delivery for any damage incurred
during transit.
Complaints must be sent to the Firm Spanesi S.p.A. in
writing within 8 days of receipt.
The warranty is valid for 12 months from the date of
purchase.
Remedy under warranty is limited to the replacement or
repair of parts that are acknowledged as defective once
they have been thoroughly examination by Spanesi
S.p.A.
Whatever the case, the purchaser shall be required to pay
transport costs and VAT. Furthermore, the warranty shall
not entitle you to claim for damages, whether direct or
indirect, or to terminate the agreement, nor shall it entitle
you to a reduction in price or to stop payments, in which
case the warranty shall cease with immediate effect.
Under no circumstances shall the replacement or repair of
the parts under warranty cause the warranty period to be
extended.
No returns will be accepted without the Manufacturer’s
written permission.
The warranty shall be void if:
• the purchaser is not up to date with payments;
• the instructions herein are not complied with;
• changes are made without the prior permission of
Spanesi S.p.A.;
•
repairs are carried out by unauthorized personnel;
• the booth is used in any way other than that
prescribed;
• original parts are replaced with parts from a different
manufacturer.
All electrical components are excluded from the warranty.
The warranty shall not be applicable if, in the opinion of
Spanesi S.p.A., the part to be replaced has been damaged
either accidentally or due to incorrect use of the booth.
For any dispute, the court of competent jurisdiction shall
be the court of Padua, Italy.
SAFETY RULES
2.2
• The booth is to be used only by the appointed
personnel, who must first read and assimilate the
contents of this manual.
• Before starting the booth, check safety devices for
damage and make sure they are in perfect working
order.
• Before commencing work, you must familiarize
yourself with the booth’s controls, paying special
attention to emergency procedures and pushbuttons,
following the instructions given herein.
• Before performing any operation, make sure there is
nobody (especially children) inside the work zone.
• Do not operate the booth outside its stated performance
range.
• Before starting the motor, make sure all controls are
set to their neutral positions.
• You must wear suitable clothing as prescribed in
this manual and by the laws in force in the country
where the booth is used. Whatever the case, do not
wear baggy clothing likely to flap about, belts, rings,
bracelets or necklaces.
• Under no circumstances should the booth be used
until it has been earthed.
• Make sure the workstation is clean and tidy and that
tools, accessories and keys are put away in the right
place.
• Do not perform any cleaning or maintenance work,
or leave the booth unattended, while the motor is
running.
• Do not, under any circumstances, operate the booth
with the fixed and/or movable guards removed or with
the safety devices disabled.
• Removing or tampering with safety devices is strictly
prohibited.
• Do not perform any maintenance or adjustment on the
booth until you have read and assimilated the contents
of this manual.
• Do not perform any maintenance or adjustment
on the booth until you have switched off the motor,
disconnected the power supply and padlocked the
switch on the control panel that locks the door.
• Adjustment operations with some of the safety devices
neutralized or partially disabled must be carried out by
just one person and, while they are being carried out,
no unauthorized persons must be allowed near the
booth.
• Where possible, keep just one guard open at a time.
Once an adjustment or maintenance operation has
been completed with some of the safety devices
neutralized, the booth must be restored to its safe
condition, with all protection devices enabled, as soon
as possible.
• Strict compliance with routine maintenance procedures
indicated herein is required in order to work safely as
well as to keep the booth running efficiently.
• Make sure the safety labels are in good condition
and make sure you know what each means: they are
necessary to avoid accidents. If they have deteriorated,
been lost or belong to components that have been
replaced, new original labels must be ordered from
the Manufacturer to replace the old ones and must be
positioned as indicated herein.
• It is worth remembering that a careful operator in
good physical and mental health is the best protection
against accidents.
EMERGENCY SITUATIONS
2.3
In case of fire, use dry chemical extinguishing media.
Do not aim jets of water at the booth: they could cause
short-circuits.
