SPALDING M8660411 Owner'S Manual Download Page 17 | Manualshive

Page: 17 / 19

background image

17

09/05

ID# M866041

1

17.

After pole has been secured to the anchor plate (2) loosen nut (26),
remove cotter pin (37), and pull out pin (36). This will allow the removal
of the threaded assembly rod (14) which is no longer necessary for the
remainder of the assembly and installation of system.

35

37

36

24

26

14

25

ONLY AFTER THE ANCHOR
PLATE HAS BEEN FULLY
TIGHTENED: Remove cotter
pin (37) and pin (36) to
remove threaded assembly
rod (14) from anchor plate (2).

WARNING!

«
...
15
16
17
18
19
»

Summary of Contents for M8660411




















Reviews:

No comments

Related manuals for M8660411

Brand: Kapriol Pages: 32

Brand: SALUDA MEDICAL Pages: 61

Brand: MacDon Pages: 272

Brand: MacDon Pages: 70

Brand: Danfoss Pages: 106

Brand: Jackco Pages: 6

Brand: Garmin Pages: 14

Brand: Garmin Pages: 14

Brand: Jacto Pages: 12

Brand: Qiagen Pages: 48

Brand: Qiagen Pages: 162

Brand: Qazqa Pages: 4

Brand: Qlightec Pages: 12

Brand: Uchida Yoko Pages: 40

Brand: TEC Pages: 6

Brand: U Technology Pages: 6

Brand: VDO Pages: 15

Brand: VDO Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands