background image

Form 44201360 

 

Oct 2019 

 

 

 

   

INSTALLATION AND OPERATION INSTRUCTIONS 

INFRARED RADIANT PATIO HEATER 

                                                                  

COLD BLOCKER™ 

Models

:

 WB10CE-N7 and L7 

Two Stage (or Single stage) 

UNVENTED - (For all Outdoor applications 

and Indoor Non-Residential Spaces) 

 
 

 

 

 

 

 

 

FOR YOUR SAFETY: If this heater is installed indoors, it must be in a sufficiently ventilated space. Exhaust fans 
MUST be operating on an appropriate cycle when heaters are operating to avoid a high concentration of carbon 
monoxide.  When  installed  in  insufficient  ventilated  spaces  this  heater  may  give  off  carbon  monoxide,  an 
odorless  and  poisonous  gas.  CARBON  MONOXIDE  POISONING  MAY  LEAD  TO  DEATH.  Early  signs  of  carbon 
monoxide poisoning resemble the flue with headaches, dizziness and nausea. If you experience these signs, GET 
FRESH  AIR  IMMEDIATELY!  Have  the  heaters  serviced  as  soon  as  possible  and  check  the  ventilation  into  the 
building. 

 

!

IMPORTANT:

 

SAVE THIS MANUAL FOR FUTURE REFERENCE. 

 

Gas Fired Products (UK) Ltd.

 

Chapel Lane, Claydon, Ipswich, Suffolk IP6 0JL, England  

Phone  01473 830551 

  Fax  01473 832055 

  www.spaceray.co.uk  

  email:  

[email protected] 

 
 

OWNER 

/

 INSTALLER: 

For your safety this manual must be carefully and thoroughly read and understood before 

installing, operating or servicing this heater. This heater is intended for use with either Natural Gas or Propane 
Gas. It must be installed by a qualified service person or a licensed contractor in accordance with state and local 
codes.  
 

:

  Improper  installation,  adjustment,  alteration,  service,  or  maintenance  can  cause  property 

damage,  injury  or  death.  Read  the  installation,  operation  and  maintenance  instructions  thoroughly  before 
installing or servicing this heater. For assistance or additional information, consult a qualified installer, service 
agency or the gas supplier. 
 
For  Indoor  Installations  INSPECT  all  combustion  air  openings  into  the  building  and,  if  necessary,  clear  if  they 
become blocked.

 

INSTALLER:

 This manual is the property of the owner. Please present this manual to the owner when you leave 

the job site. 

 

IF YOU SMELL GAS: 

 

DANGER

 

 

1. Shut off gas to the appliance. 
2. Extinguish any open flame. 

3.  If  odor  continues,  keep  away  from  the 

appliance  and  immediately  call  your  gas 
supplier. 

 

DO NOT store or use petrol or other flammable 
vapors and liquids in the vicinity of this or any 
other appliance. 

  

 
An LP-cylinder not connected for use shall not 
be  stored  in  the  vicinity  of  this  or  any  other 
appliance.

 

 

 

 

Summary of Contents for COLD BLOCKER WB10CE-L7












































Reviews: