manualshive.com logo in svg

SOYO SY-6IZM, User Manual

Share
Download
SOYO SY-6IZM User Manual Download Page 63

BIOS Setup Utility

SY-6IZM/3

60

3-8.3 FDC Controls
FDC Controls

Setting

Description

Note

Disabled

Turn off the on-board
floppy controller

Onboard FDC
controller

Enabled

Use the on-board
floppy controller

Default

3-8.4 Onboard Serial Ports
Onboard Serial
Ports

Setting

Description

Note

Disabled
3F8/IRQ4

Default
(port 1)

2F8/IRQ3

Default
(port 2)

3E8/IRQ4
2E8/IRQ3

Onboard UART 1
Onboard UART 2

Auto

Choose serial port 1 &
2's I/O address.
Do not set port 1 & 2 to
the same address
except for Disabled or
Auto.

Normal

Default

IrDA

UART Mode Select

ASKIR

The second serial port
offers these InfraRed
interface modes.

If [UART Mode Select] is set to [IrDA]/[ASKIR]

RxD, TxD Active

Hi, Hi, Lo, Lo,
Lo, Hi, Hi, Lo

This item allows you to
determine the active of
RxD, TxD.

Enabled

Default

IR Transmission
Delay

Disabled

Check with your IR-device
provider for exact setting.

3-8.5 Onboard Parallel Ports
Onboard Parallel
Ports

Setting

Description

Note

378H/IRQ7

Default

3BCH/IRQ7

Onboard Parallel
Port

278H/IRQ5

Choose the printer I/O
address.

Summary of Contents for SY-6IZM















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands