AR-837-EA
V210824
ACCESS & INDUSTRIAL CONTROL
H. Arming Password
J. Duress Code
K. Terminal Port
I. Arming Delay Time
Access programming mode
→
Parameters[1]
→
Arming PWD
→
Input 4-digit PIN (0001~9999; Default: 1234)
→
Succeeded
Or via 701Server and set it on AR-829E screen
3
8
Or via 701Server to set it on AR-829E-V5 screen
※
Duress Code is only available in networking mode. It will substitute a personal pin code and send the message of Duress to computer as a
warning signal.
Access programming mode
→
Parameters[2]
→
Duress Code
→
4 sets (select one)
→
Input 4-digit PIN (0001~9999)
→
Succeeded
4
7
Access programming mode
→
Tools
→
Terminal Port
→
0:Lift ; 1:Host ; 2:LED ; 3:PRN (default value:1)
→
Baud Selection
(default value:9600)
→
Succeeded
5
4
L. Setting up the alarm / arming
Conditions:
1. Arming enabled
2.Alarm system connected
Situations:
1. Door is open overtime
: Door is open longer than door relay time plus door close time.
2. Force open
(Opened without a valid user card): Access by force or illegal procedure.
3. Door position is abnormal
: Happening when power is off and then on again, besides, reader was on arming before power went off.
Access programming mode
→
Parameters[1]
→
ArmingDelayTm
→
Enter armed sta. Delay time(Sec), Range:000~255
；
Armed pulse out-put time (10ms) ,Range
：
000~255
→
Succeeded
3
7
F. Enroll/Delete Face
Adding
Access programming mode
→
User Setting
→
Delete Face
→
Key in 5-digit user address
→
Follow the instruction on LCD Screen to enroll face
→
Succeeded
2
6
Deleting
Access programming mode
→
User Setting
→
Delete FP
→
Key in 5-digit user address
→
Succeeded
P.S. If want to delete all users’ face data’ FP, key in
99999
2
7
#
G. Access Mode
Access programming mode
→
User Setting
→
Access Mode
→
Key in 5-digit user address (00000~08999)
→
0: Invalid; 1:Card; 2: Card or PIN; 3: Card and PIN
(
837-EA
: →
Face Identify: 0: Must ; 1: Ignore )
→
Succeeded
2
2
Access Mode
Face Identify (837-EA Only)
Result (837-EA Only)
Hardware 701Client
Hardware
701Client
0:Invalid
0: Must
Just Face
Just card control
Invalid User
1: Ignore
Just Face
Just card control
1:Card
0: Must
Just Face
Just card control
Face+Card
1: Ignore
Just Face
Just card control
1. Card Only
2. Face Only
2:Card or PIN
0: Must
Just Face
Just card control
1. Face+Card
2. Face+PIN
3. Card+Face+PIN
4. Card+Face+Card
5. PIN+Face+PIN
6. PIN+Face+Card
1: Ignore
Just Face
Just card control
1. Card Only
2. PIN Only
3. Face Only
3:Card and PIN
0: Must
Just Face
Just card control
Face+Card+PIN
1: Ignore
Just Face
Just card control
1. Card+PIN
2. Face+PIN
E. PIN Code
Access programming mode
→
User Setting
→
Enroll Face
→
Input 5-digit user address
→
Input 4-digit PIN (0001~9999)
→
Succeeded
Or via 701Client set it on Users screen
2
1
Access programming mode
→
User Setting
→
Access Mode
→
Input User Address
→
0: Invalid; 1: Card ; 2: Card or PIN; 3: Card & PIN
2
2
Setting up the access mode
Access programming mode
→
Add/Delete
→
Delete -> ID #
→
Input Site Code
→
Input Card Code
1
6
Deleting Tag by Tag ID
