Sovema TDF-M EXT 180 Operation And Maintenance Manual Download Page 43

Page: 43 / 45

OPERATION & MAINTENANCE MANUAL

Revision 2022

_____________________________________________________________________________________

A2 - 1/3

SOVEMA PRODUCT RANGE

IXED

OTARY

ILLERS WITH CHAIN OR GEARS DRIVE

• over 100 different models
• for tractors from 20 hp to 130 hp
• working width from 100 cm to 350 cm

IDE

HIFT

OTARY

ILLERS

• 10 different models

• for tractors from 20 hp to 45 hp
• working width from 100 cm to 150 cm

TONE BURIERS

• 5 different models

• for tractors from 35 hp to 90 hp
•

working width from 120 cm to 200 cm

OTARY

ARROWS

• 11 different models

• for tractors from 25 hp to 100 hp
• working width from 110 cm to 300 cm

OLDING ROTARY

ARROWS

• 3 different models

• for tractors from 200 hp to 350 hp

• working width from 500 cm to 700 cm

OTARY

ITCHERS

(

FIXED OR WITH SIDE SHIFT

)

• 11 different models

• for tractors from 40 hp to 120 hp

• working depth from 45 cm to 130 cm

Summary of Contents for TDF-M EXT 180














































Search results

Summary of Contents for TDF-M EXT 180

Reviews:

Brands by name

Popular brands

Sovema TDF-M EXT 180, Operation And Maintenance Manual

Search results

Summary of Contents for TDF-M EXT 180

Reviews:

Brands by name

Popular brands