Questions? Call Toll Free at 1-800-737-2112
Copyright © 2015 MAT Engine Technologies, LLC
EN - 6
Edger Specifications
• Save all instructions
Parts & Features
Unit Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 lb. (27kg)
Cutting Depths . . . . . . . . . . . . . . . . . . . 0-2.5 in. (0-63 mm)
Blade Diameter. . . . . . . . . . . . . . . . 9 in. (228 mm), 3 point
Gasoline Type . . . . . Regular Unleaded / 87 Octane (min.)
Gasoline Capacity . . . . . . . . . . . . . . . . . . . . . 1.7 qt. (1.6L)
Oil Type (API SG-SL) . . . . . . . . . . 10W-30 is recommended
for all service temperatures.
See page 7 for additional information.
Oil Capacity . . . . . . . . . . . . . . . . . . . . . . . . . 12 oz (355 ml)
Spark Plug Model. . . . . . . . . . . . . . . . . . . . . . Torch E7RTC
Spark Plug Gap . . . . . . . . . . . 0.024-0.028 in. (0.6-0.7 mm)
Engine Type . . . . . . . . . . . . . . . . . . . . . . . . . 4 Stroke OHV
Displacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79cc
RPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3600 RPM
Torque Rating. . . . . . . . . . 3.1 ft-lbs torque per SAE J1940
Bore Diam. x Stroke. . . . . . . . 2.03X1.50 in. (51.6X38 mm)
Intake Valve Clearance . 0.0079-0.0098 in.(0.20-0.25 mm)
Exhaust Valve Clearance . 0.0098-0.012 in.(0.25-0.30mm)
Angle of Ignition . . . . . . . . . . . . . . . . . . . . . . . . 25 Degrees
1. START LEVER
Lever on handle which allows the engine to
run. When lever is released, engine will stop.
2. CHOKE CONTROL
Restricts the air intake. This allows
for an enriched fuel-air mixture which helps to start
the engine.
3. MUFFLER
Location of engine exhaust.
4. ADJUSTABLE REAR WHEEL
Right rear wheel is adjustable to
level the edger when edging along a curb (curb-hopping).
5. ADJUSTABLE FRONT WHEEL
Front wheel is adjustable from
side to side for balance. The front wheel can also adjust
down for curb-hopping.
6. RECOIL STARTER HANDLE
The engine is equipped with an
easy pull recoil starter.
7. INDEX LEVER
Permits adjusting the cutting angle to 15
degrees, 0 degrees (vertical), or -15 degrees. To change
the angle, pull the index lever and rotate the quill
assembly to the desired angle.
8. BLADE
Rotating cutting element.
9. BLADE GUARD
Prevents stones and debris from being
thrown at the operator.
10. SPARK PLUG/SPARK PLUG WIRE
Provides spark to ignite air/
fuel mixture. The Spark Plug Wire must be disconnected
and moved away from the Spark Plug when servicing
the unit.
11. AIR FILTER
Removes debris and contaminates from
intake air, allowing engine to run smoothly with low
exhaust.
12. DEPTH SELECTOR PLATE
13. DEPTH CONTROL LEVER,
14. CONTROL ROD
Used to control the edging depth of cut.
15. GROUND WIRE TERMINALS
Must be connected for the
Start Lever to function.
Figure 1
REAR VIEW
FRONT VIEW
1
6
2
4
5
9
8
7
3
10
13
12
14
11
15
