background image

27

TO REMOVE WHEEL FOR REPAIRS 

FRONT WHEEL -

1.   Block up axle securely.
2.   Remove axle cover, retaining ring and 

washers to allow wheel removal.

3.   Repair tire and reassemble.
4.   Replace washers and snap retaining 

ring securely in axle groove.

5.   Replace axle cover.

TO START ENGINE WITH A WEAK BAT-
 TERY 

WARNING:

  Lead-acid batteries gen-

 er ate ex plo sive gases.  Keep sparks, fl ame 
and smoking ma te ri als away from bat-
 ter ies.  Always wear eye pro tec tion when 
around batteries.
If your battery is too weak to start the 
engine, it should be recharged. (See "BAT-
TERY" in the MAINTENANCE section of 
this man u al).
If “jumper ca bles” are used for emer gen cy 
starting, follow this pro ce dure:

IMPORTANT

:  Your tractor is equipped 

with a 12 volt system. The other vehicle 
must also be a 12 volt system. Do not use 
your tractor battery to start other vehicles. 

TO ATTACH JUMPER CABLES -
1.   Connect one end of the RED cable 

to the POSITIVE (+) terminal of each 
battery(A-B), taking care not to short 
against tractor chassis.

2.   Connect one end of the BLACK ca ble 

to the NEGA TIVE (-) terminal (C) of 
fully charged battery.

3.   Connect the other end of the BLACK 

cable (D) to good chassis ground,  
away from fuel tank and bat tery.

TO REMOVE CABLES, REVERSE 
ORDER -
1.   BLACK cable fi rst from chassis and 

then from the fully charged battery.

2.   RED cable last from both batteries.

0066

3sq

Retaining 
Ring

Washers

Axle 
Cover

TO AD JUST STEER ING WHEEL ALIGN-
 MENT

If steering wheel crossbars are not 
hor i zon tal (left to right) when wheels are 
positioned straight forward, remove steer-
 ing wheel and reassemble with crossbars 
horizontal. Tighten securely.

FRONT WHEEL TOE-IN/CAM BER

The front wheel toe-in and camber are not 
adjustable on your tractor.  If damage has 
occurred to affect the front wheel toe-in or 
camber, contact a qualifi ed service center. 

REAR WHEEL -
1.   Block rear axle securely.
2.   Remove fi ve (5) hub bolts to allow 

wheel removal.

3.   Repair tire and reassemble.  Replace 

and tighten hub bolts securely.

NOTE: 

To seal tire punctures and prevent 

fl at tires due to slow leaks, tire sealant 
may be purchased from your local parts 
dealer. Tire sealant also pre vents tire dry 
rot and corrosion.

1428

Belt 
Keeper

Engine 
Pulley

V-Idler

Engine 
Pulley

Clutching Flat Idler

Clutching 
Idler

Belt 
Keeper

Belt 
Twists

Above 
Midspan 
Belt Keeper

Belt 
Keeper

Transaxle 
Pulley

V-Idler

TRACTOR V-BELT DRIVE SCHEMATIC 

VIEWED FROM L.H. SIDE OF TRACTOR

AS VIEWED FROM BOTTOM

7.   Reinstall mower drive belt onto electric 

clutch pulley.

IMPORTANT:  

Check Brake Adjustment.

For Parts Call K&T 606-678-9623 or 606-561-4983

www.mymowerparts.com

Summary of Contents for Southern States SPGT2254



































Reviews: