background image

 

 

                                                                                                      South-Tek Systems 

Version:

 0

 

Revision Date: 6/29/18

                                                                                                           

Page 5 of 18 

1

 

INTRODUCTION 

1.1

 

PURPOSE 

The 

BrewBlast™  110CPH

  provides  an  economical,  precise  means  of 

supplying nitrogen 

to “push” the 

cold brew coffee to the tap within café and 

coffee-serving establishments. 
 
South-

Tek  System’s  line  of  B

rew

Blast™  products  consist  of  an  internal  N

2

 

generator and an integrated compressor.  Since air is comprised of ~79% 
N

2

 we simply and cost-effectively separate the N

2

 from the air.   Nitrogen is 

an  inert  gas  (non-combustible),  which  is  even  used  to  package  food 
products for increased shelf life.  The N

2

 

is “generated” by 

our membrane 

technology,  where  compressed  air  is  forced  through  a  separation  media 
and  O

2

  is  exhausted  to  atmosphere  and  N

2

  is  allowed  to  pass  through  to 

process. 

1.2

 

AUDIENCE 

This  manual  is  intended  for  Installer/Restaurant/Bar  Operator/Supervisory 
Staff and should be read in its entirety prior to operation. 
Please contact your local provider for any operation and maintenance first 
prior to contacting the manufacturer. 
 

1.3

 

IMPORTANT INFORMATION 

Before personnel attempt to service the unit, ensure the power switch has 

been  turned  to  the  off  position,  and  then  disconnect  the  unit’s  external 

power  cord  from  the  building  electrical  power  supply  if  possible.    Always 
follow specific manuals from STS when servicing your system. 

 

 

Summary of Contents for BREW BLAST 110CPH



















Reviews: