background image

 

 

                                                                                                      South-Tek Systems 

Version:

 0

 

Revision Date: 6/29/18

                                                                                                           

Page 10 of 18 

 

After  the  nitrogen  storage  tank  is  depleted  down  to  the  cut-in 
pressure  (~60  PSIG)  the  generator  will  turn  back  on  and  refill  the 
system. 

 

3.4

 

STARTING & STOPPING 

 

To 

start 

the 

generator simply push the green 
power switch on the front of the 
generator to the ON(up) position. 

Note:  On  startup  the  generator 
will  have  a  12  second  delay 
before 

the 

compressor 

operates.  This  is  designed  to 
prevent 

damage 

to 

the 

compressor. 

 

At  this  point  the 

power  switch  will  be  illuminated 
and  the  generator  will  be 
operating normally. 

 

The  system  has 

two  main  run  modes 

  Run  and 

Standby. 

When 

the 

green 

(Operate)  power  switch  is  turned  on  and  illuminated,  the  internal 
controller will automatically determine which mode to enter. 

 

If the BrewBlast

™ 

is in run mode, the standby light will be off and the 

nitrogen generator will be filling the storage tank with nitrogen. 

 

If  the  BrewBlast

  is  in  standby  mode,  the  standby  light  will  be 

illuminated;  the  nitrogen  generator  will  be  off  and  waiting  until  the 
storage tank pressure drops the cut-in pressure to turn back on. 

 

If the 

BrewBlast™ 110CPH

 runs continuously for more than 9 hours, 

the  BlastOff  Alarm  will  shut  down  the  generator  (see: 

4.2 

for  more 

details) 

 

 

Summary of Contents for BREW BLAST 110CPH



















Reviews: