background image

-42-

For Machines Mfg. Since 3/11

16-Speed Gearhead Lathe

O P E R A T I O N

2.

  Rotate the adjustment cap screws in opposite 

directions for the desired offset (see the 
illustration in 

Figure 50

).

3.

  Retighten the clamping hex bolts underneath 

the tailstock to secure the offset.

Aligning Tailstock to Spindle 
Centerline

This is an essential adjustment that should be 
verified or performed each time the tailstock 
is used to turn concentric workpieces between 
centers or immediately after offsetting the 
tailstock when turning a taper. If the tailstock is 
not aligned with the spindle centerline when it is 
supposed to be, turning results will be inaccurate 
along the length of the workpiece.

Items Needed 

Qty

Hex Wrench 6mm .................................................1
Wrench 17mm .......................................................1
Round Stock 2" x 6" ...............................................2
Precision Level ......................................................1

To align the tailstock offset to the spindle 
centerline:

1.

  Use the precision level to make sure the 

bedway is level from side-to-side and from 
front-to-back.

— If the bedway is not level, correct 

this condition before continuing with 
this procedure (refer to 

Leveling & 

Mounting 

on 

Page 24

).

2.

  Center drill both ends of one piece of round 

stock, then set it aside for use in 

Step 5

.

Note:

 

As long as this dead center remains in the 

chuck, the point of the center will remain 
true to the spindle centerline. The point will 
have to be refinished whenever the center is 
removed and then returned to the chuck.

4.

 

Install a center in the tailstock.

5.

  Attach a lathe dog to the test stock from 

Step 2

, then mount it between the centers 

(see 

Figure 53

 for an example).

Figure 53. Example photo of stock mounted between 

the centers.

6.

  Turn 0.010" off the stock diameter.

7.

 

Mount a test or dial indicator so that the 
plunger is on the tailstock quill.

Figure 52. Turning a dead center.

3.

  Use the other piece of round stock to make 

a dead center, and turn it to a 60° point, as 
illustrated in 

Figure 52

.

Downloaded from 

www.Manualslib.com

 

manuals search engine

 

Summary of Contents for SB1053









































































































































Reviews: