background image

MIDI Features 

The Hub v1 uses MIDI PC messages for saving and recalling scenes.  Additionally, the Hub can also 
respond to MIDI Continuous Control (CC) messages and MIDI Clock. 
 
MIDI CC messages received by the Hub are passed on to the connected Soundblox 2 pedals.  The 
function of each CC number is hard mapped to pedal functions across the Soundblox 2 line.  The 
implementation table is available at the end of this document.  Each pedal type has an assigned 
CC number mapping so that they can be used as a single system when connected to the Hub. 
 
The Hub can also accept MIDI Clock messages to synchronize LFOs on Soundblox 2 pedals that 
support this function.  This allows an external MIDI device to set the LFO rate on an effect by 
sending a MIDI Clock stream to the Hub.  The MIDI Clock is sent to simultaneously to attached 
pedals so it’s possible to use MIDI Clock input to synchronize LFOs between two or more pedals. 
 
The MIDI Output functions as a MIDI Thru connection by default.  This means that any incoming 
MIDI messages are immediately sent back out on the MIDI Out jack.   However, it’s possible to use 
the Hub Manager application to change the mode of the MIDI Out.  For example, it can be set to 
take incoming Expression and Hot Hand messages and send them on the MIDI Out as Continuous 
Control messages.   Other modes will likely be supported in future firmware/software revisions. 

Specifications 

Weight: 6 oz. 

Dimensions: 3.8 in. (W) x 2.1 in. (L) x 1.4 in. (H) 

Power requirements:  9 Volts DC @ 40mA (up to 80mA with Hot Hand accessories)  

Power plug size:  2.1mm (inner dia.), 5.5mm (outer dia.)  center negative, barrel positive 

Expression Pedal input: Stereo ¼ in. plug, tip hot, 10k-50k Ohm resistance.  Linear type. 

Multi-Function connector: 4 conductor, 3.5mm plug

 

Summary of Contents for Soundblox Hub v1








Reviews: