background image

DESIGN FEATURES 

Hand-crafted in the U.S.A.  with mil-spec glass epoxy circuit boards, low-
loss connections, gold-plated input connectors, and metal film resistors. 

Darlington High Current Output Topology - Soundstream's 
"overbuilding" of the output section incorporates Darlington output devices 
sandwiched between the circuit board and the heatsink in a design called 
Chassisink™ to ensure cool, efficient amplifier operation. 

    

Mixed Mono Capable so you can simultaneously drive a stereo and mono 
load (satellites and subwoofer).   

2 Ohm Drive Ability - The satellite channels of the USA•305 amplifier are 
designed to drive loads down to 2 Ohms stereo (5 channel mode) and 4 
Ohms bridged (3 channel mode).  The subwoofer channel of the USA•305 
is designed to drive loads down to 2 Ohms. 

           

Built-in Staggered Crossover - Built in 2-way electronic crossover is 
designed to send either high or low pass information to the amplifier. 

Bass EQ - Adjustable bass equalization circuit allows you to boost bass by 
as much as +9 dB at 45 Hz.  A built-in subsonic filter helps to protect 
speakers. 

Drive Delay™ Muted Turn-on/off Circuit - A unique circuit which 
completely eliminates any amplifier-related turn-on/off noises. 

Flexible Input Sensitivity - Accepts input voltages from 100 mV to 2.5 V, 
which permits maximum output from amplifier with virtually any source 
unit. 

Differential Balanced Input Topology for added immunity to ground 
loops caused by component and vehicle electrical system interaction. 

 

 

Power 

4 ohms

 

Power 

2 ohms

 

Bridged Power 

4 ohms

 

USA•305

 

35w x 4 + 

100W X 1

 

60w x 4 +  

160w x 1

 

120w x 2 

15 

USA•305 

System Configuration #2: 
 

One pair of stereo inputs 

Four channels driving satellites in high pass 

Internal inputs to channels 3 & 4 

Subwoofer channel driving two subwoofers in low pass 

Internal inputs to the subwoofer channel 

Internal crossovers used 

Summary of Contents for USA 305











Reviews: