RADIO OPERATION
NOTE:
NOTE:
COMPACT DISC OPERATION
1. Slide the CD/RADIO switch to the RADIO position.
2. Slide the Band switch to a specified band.
3. Rotate the Tuning control to the desired station.
4. Adjust the Volume control to a comfortable listening sound level.
5. For AM(MW) band, better reception can be obtained by rotating the set. For
FM band, the FM Aerial Wire (thin black wire) which serves as FM aerial,
must be stretched to its full length.
When you are receiving FM Stereo program, the FM Stereo indicator
will be steady on.
6.
If a particular FM (STEREO) station is weak, or you hear too much
background noise, try moving the position of the band selector switch
to the FM (MONO) position. This can often result in a much clearer
reception.
The radio can be switched off by setting FUNCTION switch to OFF position.
i
i
i
i
Always protect a disc against scratches, soil and dust etc. It is
recommended that during non-use periods the discs should be
retained in the original case. If a disc is treated with
reasonable care, the only maintenance likely to be needed to
retain the excellent sound reproduction is wiped off with a cloth
as indicated.
To handle a disc use only one of the two manners illustrated.
(Do not touch the rainbow - colored side)
To wipe a disc, use only a soft cloth. Do not use benzene or
thinner which will damage the disc. The disc should always be
wiped in a straight line from the center to the edge. It should
never be wiped in a circular motion.
Never place the disc on other equipment or near any heat
source. Avoid positions where the disc would be subjected to
direct sunlight for long periods.
LISTENING TO A COMPACT DISC
1. Set the CD/RADIO switch to CD position.
2. Press the Open button to open the CD Door, place a CD with the printed
side up into the CD compartment
3. Press the corner of the CD door to close the lid, the disc will rotate and the
LED Display will show the disc's total number of tracks.
4. Press the CD Play/Pause Button:
Press once the play starts from the first track.
n
n
Press this button in play mode and the playback will be paused. To
resume playback from the same point, press the button again.
5. Press the CD Skip/Search buttons during play to skip to the desired track.
Press the CD Skip/Search up button to skip to the next track on the disc.
Press the CD Skip/Search Down button to skip to the beginning of the track
currently playing.
Press and hold the CD Skip/Search buttons during play to scan the disc
at high speed. When the desired section of the disc is found, release the
button, normal play will resume.
6. Press CD Stop
n
button to stop CD playing.
PROGRAMME PLAY
NOTE:
REPEAT PLAY OPERATION
SINGLE TRACK REPEAT
ALL TRACKS REPEAT
Up to 20 tracks can be programmed for disc play in the order you like or the
same track (song) can be repeated up to 20 times.
Programming can only be done during stop mode.
1. Press the PROGRAM button in stop mode.
2. The display will show " 0 " flashing and the PROGRAM indicator will flash.
3. Press the SKIP/SEARCH buttons until the desired track shows in the display.
The PROGRAM indicator keeps flashing.
4. Press the PROGRAM button. The first track is now stored into memory, and
" 0 " flashes in the display again waiting for your next selection.
5. Repeat steps 3 and 4 until all the desired tracks are programmed.
6. When you have finished programming, press the PLAY/PAUSE button.
7. The display will show the track number being played, and the PROGRAM
indicator will keep flashing during program play.
8. All songs will be played in the order you programmed.
9. If you want to hear the next song while playing, press the SKIP/SEARCH
buttons.
10. When all the songs have finished, the set will stop. The PROGRAM indicator
will turn off. To play the programmed tracks again, press the PROGRAM
button, then press the PLAY/PAUSE button.
11. To erase the programme, press the PROGRAM button and then press STOP
button.
To repeat the SAME track over and over again, do the following.
1. Press the Skip/Search Button during playback to select the track you want to
repeat.
2. Press the Repeat Button. The Repeat Lamp will flash.
3. The track you selected will play over and over, till you press Stop Button.
4. To stop the repeat function, press Repeat Button twice.
To repeat ALL TRACKS on a disc and then play them again and again, do the
following.
1. Press Repeat Button twice during playback. The Repeat Lamp will be
constantly on.
2. All the tracks on the CD will play in order and then start all over again. To stop the
repeat function, press Repeat Button once.
5
4
