Soundigital POWER SPORTS 2400.1 EVOPS Owner'S Manual Download Page 10

INSTALLATION SEQUENCE

Ø

Mount the amplifier in such a way you have access to the connectors;

Ø

Install the power cables in the vehicle/vessel properly, starting from the battery to the 
fuse  holder  or  circuit  breaker,  use  the  cable  with  the  appropriate  size.  Make  all 
connections, install fuse holders or circuit breakers, but without placing the fuses or 
with the circuit breakers in the "OFF" position;

Ø

Connect  the  power  cables  in  to  the  amplifier,  observing  the  polarity.  Connect  all  the 
positive cables from the fuse holder or circuit breaker to the positive conector of the 
amplifier and all the negative power cables from the batteries to the negative connector 
of the amplifier;

Ø

The ground cable must be as short as possible and must be connected to the negative 
connector of battery or vehicle chassis in case of metallic chassis;

Ø

Install the signal input cables in a proper way, distant from the power cables;

Ø

Connect the RCA or the High level signal input cables to the head unit and amplifiers;

Ø

Install the audio output cables with the appropriate section, distant from the power and 
audio input cables;

Ø

Connect the audio output cables to the amplifier and speakers respecting the positive 
(+) and negative (-) polarities;

Ø

Install the remote cable with the power cables, using 1.5mm² (15 AWG) cable or thicker;

Ø

Connect  the  remote  power  cable  to  the  amplifier's  "REM"  terminal  at  the  main  unit's 
remote power output (when not using the high level signal inputs);

Ø

Before  powering  the  system,  verify  all  the  connections  and  make  sure  there  are  no 
mistakes or short-circuits on the power and ground cables;

Ø

;

Reconnect the ground of the batteries

Ø

Check  if  the  head  unit  is  turned  off  and  then  place  the  fuses  in  the  fuse  holders  or 
switch the circuit breakers on;

Ø

Turn on the main unit and the amplifier will turn on the "ON" LED indicating that it is in 
operation.

Warning!

Warning!

Remove the paint between
the terminal and chassis

Ø

THE MAX: DISTANCE FOR THE INSTALLATION OF THE FUSE/CIRCUIT BREAKER 
IS 12 INCHES (30 CM) AWAY FROM THE BATTERY.

10

Summary of Contents for POWER SPORTS 2400.1 EVOPS
















Reviews: