SoundDigital 600.4 EVO 4.0 Owner'S Manual Download Page 8 | Manualshive

Page: 8 / 14

background image

8

We recommend the use of ONLY OFC (Oxygen Free Copper) Cables on the
installation of our products.

AUDIO INPUTS

RCA Inputs

All RCA Inputs must be connected for
the 4 channels to work.

600

WRMS

ELECTRICAL DIMENSIONING AND AUDIO INPUTS

ELECTRICAL DIMENSIONING

For proper operation of your SounDigital amplifier, you need the proper
dimensioning of the electrical system and the cables used.

The table below shows the minimum section of GND cables, +12VDC cables and
speaker output cables according to the power generated by the amplifier.

POWER CABLE

GROUND CABLE

SPEAKER CABLE

10mm² - 7 AWG

«
...
6
7
8
9
10
...
»

Summary of Contents for 600.4 EVO 4.0















Reviews:

No comments

Related manuals for 600.4 EVO 4.0

Brand: LABTEC Pages: 12

Brand: NAD Pages: 3

Brand: T-audio Pages: 13

Brand: Takstar Pages: 24

MDi2 1K4-2K7-6K

Brand: RAM Pages: 13

Brand: Harman Kardon Pages: 8

Brand: Unison Research Pages: 21

Brand: e-motion Pages: 9

BDA-PS9-37/37-90-C

Brand: G-Wave Pages: 18

Brand: PTN Pages: 2

Brand: Ericsson Pages: 34

Brand: JBL Pages: 8

Brand: NAD Pages: 33

Brand: PKN Controls Pages: 9

Brand: Advance Paris Pages: 16

Brand: Randall Pages: 10

Brand: Tokyo Pages: 11

1812R Blues King 12

Brand: SUPRO Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands