Sound Storm SSV7HRB, User Manual, Page: 2 / 13

On a towel or soft cloth, gently place the monitor assembly “face down” on a stable
worksurface.
Using the wires provided, complete the audio, video and power connections in
your vehicle as shown in the diagram below.
Carefully remove the headrest and set it down
in an uncluttered work are. Take the appropriate
precautions to ensure it is not damaged during
installation.
Push on the headrest with your fingers to make
sure there are no obstructions inside that would
interfere with the installation. After you confirm
that there are no internal obstructions, take the
paper template provide in place, and mark the
area to be cut.
Using a sharp, adjustable-depth blade knife,
make a diagonal cut beginning 1/4" INSIDE
from one corner, and ending 1/4" INSIDE from
the opposite corner.
Repeat, cutting diagonally between the two
other corners.
Set the adjustable blade to 1" depth, and cut
around the edges of the hole, staying 1/4"
inside the edge. Pull up one corner of the foam
rectangle, and use the blade to cut underneath
– remove a small section at a time, using the
"pull up and cut" method for uniform depth.
If necessary, use a Dremel tool or other appro-
priate tool to remove any other obstructions
present.
Using a sharp scissors, cut the points offf the
flaps of upholstery material to about 3/4" - 1"
wide.
Route the cable through the opening just cut,
and out the bottom of the headrest. If possible,
conceal the cable using a gear shift covering
or similar. Then fold the four flaps into the
cavity in the headrest.
Slide the trim frame onto the monitor
shroud and slide the assembly into the
cavity in the headrest. As you do this,
feed the cable through the headrest as
shown in the diagram. Secure the shroud
with the three screws as shown.
Connect the RCA cables and the power
cable, and slide the monitor into the
shroud until you feel a click. As you do
so, push the cables into the headrest
shround so they travel into the area behind
the shroud and out below the headrest.
Carefully peel back the upholstery material.
VIDEO SOURCE 1
(DVD player, video game, etc.)
VIDEO SOURCE 2
(DVD player, video game, etc.)
CONTENTS
SSV7HRB User’s Manual - Contents
U S E R ’ S M A N U A L
SSV7HRB User’s Manual - page 7
SSV7HRB User’s Manual - page 10
SSV7HRB User’s Manual User’s Manual - page 2
General precautions
Safety precautions
SSV7HRB User’s Manual User’s Manual - page 3
SSV7HRB User’s Manual - page 4
Features What is included?
Monitor Controls and Features
SSV7HRB User’s Manual - page 5
SSV7HRB User’s Manual- page 6
Troubleshooting
SSV7HRB User’s Manual - page 11
Specifications
SSV7HRB User’s Manual - page 12
Remote Control
SSV7HRB User’s Manual - page 8 SSV7HRB User’s Manual - page 9
• Do not operate this equipment while
driving – safe driving should always
be your highest priority.
• This product should not be installed
in a location which allows the monitor
screen to be visible to the driver of the
vehicle. In some states and countries,
the viewing of images on a screeen
inside a vehicle is illegal, even by
people other than the driver. Be sure
that the installation and operation of
this system is in compliance with local
rules and regulations.
• If you have installed the monitor in
a position where it is visible to the
driver, be sure to install a Safety Cord.
Wire this cord to an accessory wire
which has +12v power when the
ignition is switched on. This will prevent
the operaton of the monitor when the
engine is running.
• Do not open or attempt to repair this
unit yourself. Dangerous high voltages
are present which may result in electric
shock. Refer any repairs to a qualified
service technician.
• Do not attempt to repair a damaged,
broken or faulty power cord. Replace
it with a new one immediately.
• To avoid risk of electronic shock or
damage to the monitor, do not permit
any of this equipment to become damp
or wet from water or drinks. If this does
occur, immediately unplug the power
cord and send the monitor to your
local dealer or service center as soon
as possible.
• if there is smoke or any peculiar odor
present during useor if there is damage
to any of the component enclosures,
immediately unplug the power cord
and send the monitor to your local
dealer or service center as soon as
possible .
If you do not know how to install the
Safety Cord
, please consult with a
mobile video installer in your area, and
have this work completed properly
before operating the video system.
When first unpacking your new flip-
down monitor, please check first that
the package contains all of the items
below. If something is missing, contact
the store where you purchased the
player.
• LCD monitor
• Mounting shroud
• Trim bezel
• Wireless remote control with
batteries
• RCA-RCA video cable
• Video/power interface cable
with inline fuse
• Monitor removal key
• Mounting screws
If you experience operation or performance problems with this product, compare your
installation with the electrical wiring diagram on the previous page. If problems persist,
read the following troubleshooting tips which may help eliminate the problems.
2 General precautions
2 Safety precautions
3 Installation precautions
3 Operation precautions
4 Features
4 What is included?
5 Monitor controls and features
6 Remote control
6 Remote control battery replacement
7 System wiring
8 Monitor installation
10 Relmoving the monitor
11 Troubleshooting
12 Specifications
Congratulations on your purchase
of a Sound Storm Video Monitor.
It has been designed, engineered and
manufactured to bring you the highest
level of performance and quality, and
will afford you years of viewing
pleasure.
Thank you for making Sound Storm
your choice in car video entertainment!
page
SSV7HRB
7" Headrest Widescreen
TFT Video Monitor
A/V SYSTEM
Screen size
Screen format
Video Compatability
LCD panel type
Resolution, pixels
Brightness
GENERAL
Power requirements
Power consumption
Dimensions (L x W x H)
All specifications subject to change without notice.
MODEL
SYMPTOM CAUSE REMEDY
VIDEO
INPUT 1
VIDEO
INPUT 2
Insert the removal key into the gap
on the right side of the monitor to
depress the tabs to release it.
L A B O R A T O R I E S
®
NOTE: Headrests vary in their construction. Most headrests have a plastic
plate inside into which you can directly attach the mounting screws. However,
in some cases this plate is absent or is too deeply located for attachment. In
this case, you may wish to cut a plate of wood of appropriate thickness and
hot-glue it into place to use as a mounting plate.