background image

4

10. Remove the drivers side cover directly in front of the console by removing the plastic retainer with a 
Phillip’s screwdriver and then pull the cover loose. If installing the optional amplifi er system, the passenger’s 
side panel will need to be removed as well but has no plastic retainer and can simply be pulled off. Fig. 4
11. Remove the radio trim bezel by carefully prying loose with a plastic panel removal tool. Start at the 
corners and work around the bezel. Fig. 5
12. Remove the four screws securing the radio, pull radio from dash and disconnect all wiring. 
13. Route the white two pin connecter of the subwoofer harness up to the radio opening from the drivers 
side of the console 

NOTE: If installing the optional amplifi er system, route the amplifi er harness at this time.

Subwoofer Input Connection with Optional Amplifi er

14. Connect the white two-pin connecter of the subwoofer harness to the corresponding connecter of the 
amplifi er harness at this time.

Subwoofer Input Connection without Optional Amplifi er

15. Connect the six inch adapter harness to the end of the two-
pin connecter. Locate position 40 and position 32 on the radio 
connecter and install one of the wire taps onto the wire. Lay 
the wire in the open channel, fold the connecter body over and 
squeeze with a pair of pliers until connecter snaps shut. 
Fig. 6. Connect the green wire of the adapter harness to the wire 
in position 40, and the brown wire to the wire in position 32

NOTE: If you are installing the optional amplifi er system, route the 
power and ground wires of the amplifi er body harness under the 
carpet and toward the driver’s side kick panel at this time.

16.Connect the power connecter to the power wire coming 
through the fi rewall grommet and tuck out of the way.
17. Connect the black ground wire to the factory ground point 
near the driver’s side kick panel. Torque to 9 +/- 1.5 Nm. Fig. 7

 

Fig. 4 

 

Fig. 5 

 

Fig. 6 

 

Fig. 7 

Connect ground 

wire(s) to either 

factory ground stud. 

Summary of Contents for SSON12











Reviews: