Sound Skulptor MP573 Assembly Manual Download | Manualshive

Page: 10 / 12

background image

www.soundskulptor.com

Document revision 2.3 – Last modification : 27/05/21

MP573 Assembly guide – Main PCB, A side

39. Knobs

Attach the 2 knobs, using the included 1.5mm hex key.

MP573 Assembly guide – DI board

40. Horizontal resistors

Add R59 to R61, R63 to R69.
Control the resistor values with a digital multimeter. Bend the leads at 0.4” with a lead forming tool.

41. Vertical resistor

Add R62. This resistor is placed vertically. Bend one leg 180° sharp and insert.

Copyright ©2015 SoundSkulptor

«
...
8
9
10
11
12
»

Summary of Contents for MP573













Reviews:

No comments

Related manuals for MP573

Brand: M-Audio Pages: 8

Brand: Bad Cat Pages: 9

Brand: JBL Pages: 470

Brand: JBL Pages: 27

Brand: JBL Pages: 4

Grand Touring Series GTO1004

Brand: JBL Pages: 27

Grand Touring Series GTO1004

Brand: JBL Pages: 4

Brand: Eden Pages: 21

Brand: McIntosh Pages: 20

Brand: Electro-Voice Pages: 4

Brand: Channel Vision Pages: 8

Brand: Massive Audio Pages: 6

Brand: Lanzar Pages: 16

Brand: Crunch Pages: 2

Brand: Altimium Pages: 36

Brand: Talk electronics Pages: 7

Brand: Vox Pages: 35

Brand: VAC Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands