Sound Skulptor MP 599 Assembly Manual Download Page 6

Page: 6 / 9

www.soundskulptor.com

Document revision 2.1 – Last modification : 01/12/21

MP 599 Main board Assembly guide

23. Frame assembly

Attach the side panel to the front
plate with two M3x6 black
countersunk screws.

24. PCB mounting

Put the PCB in place, switches and pots going through the front panel. Watch out for the LED position.
Attach the PCB with 4 M3x25 mm spacers and 4 shake-proof washers.

25. Knobs

Attach the 2 knobs.

26. Test

Your MP 599 is now ready for test. Please follow instructions in the “MP599 Test” document.

DI board Assembly guide

1. Horizontal resistors

Add R41 to R45, R48 to R51.
Control the resistor values with a digital multimeter. Bend the leads at 0.4” with a lead forming tool.

2. Diodes

Add D10, D11. These diodes are installed vertically, cathode (black ring) on top.

Warning

: Make sure to respect the direction of the diodes which is marked by a ring on the component

and a “k” on the PCB marking.

Summary of Contents for MP 599









Search results

Summary of Contents for MP 599

Reviews:

Related manuals for MP 599

Brands by name

Popular brands

Sound Skulptor MP 599, Assembly Manual

Search results

Summary of Contents for MP 599

Reviews:

Related manuals for MP 599

Brands by name

Popular brands