input
one
two
one
two
L
R
tape/cd
line input
mic input
Plug a microphone with an XLR
connector into mic input one or two.
The knob above the jack controls the
volume level.
The mic inputs are balanced and low impedance,
and supply phantom power (15 volts) for condenser
type microphones.
When using long mic cables,use a balanced micro-
phone to help prevent hum and interference.
Plug a balanced, line-level source
with an XLR connector (such as the
output from a mixer) into line
input one. The knob above the jack
controls the volume level.
Line input one is a balanced line level input.
Use shielded cable to avoid hum or interference.
To daisy-chain two sound systems together for
greater crowd coverage, connect the line output
from one system into line input one.
Plug any line-level source with a
1/4" phone plug (tape player, music
instrument, etc) into line input two.
The knob above the jack controls the
volume level.
Line input two is an unbalanced line level input.
Use shielded cable to avoid hum or interference.
Plug the outputs from a tape player
or external CD player with RCA
jacks into the tape/cd input. The
knob above the jack controls the
volume level.
The tape/cd input is a line level input.
This is a summing input,meaning the left and right
channels will combine for a mono input signal.
Choosing an Input
Wireless Mic Operation
CD Operation
two
one
antenna
a
b
antenna
a
b
wireless mic
wireless mic
Operating the optional Wireless System.
Raise both the left and right antennas up and out at a
45
°
angle for the wireless system in use — on top of
the unit towards front for wireless one, towards the rear
for wireless two).
Install a new 9 volt ALKALINE battery in the transmitter
for best results.
The wireless transmitter (microphone or beltpack) has
a 3-position
ON
/
STANDBY
/
OFF
switch.Be sure the switch
is in the ON position for normal
operation (use the ST.BY position
when not speaking to prevent interference).
low
high
mid
voice
loud
norm
equalizer
Using the Outputs
output
L
R
two
one
tape
line output
Set the voice switch to “loud” for
outdoor and other applications
where powerful voice projection is
needed.
Set the voice switch to the “normal”position when
playing music and for most indoor applications.
Use the 3 equalizer (tone) controls
to adjust the sound for best sound
quality and clarity. The top-center
tic mark indicates a ‘flat’ response.
For indoor and/or music playback, set all controls
to the flat (12 o’clock) position and then adjust for
desired sound quality (be sure the voice switch is
in the normal position).
For outdoor / voice applications, turn up the mid
control for better sound projection.
Setting the EQ Controls
Connect the RCA outputs
to a tape player’s input to
record the sound system.
The tape output is a line-level,
summed and composite signal of the
sound system inputs.
Connect line output one
to the balanced input of
another system for daisy-
chain applications.
Line output one is a balanced, low-
impedance and composite signal of
the sound system inputs.
Connect line output two
to a tape player’s input to
record the sound system.
Line output two is an unbalanced,
line-level and composite signal of the
sound system inputs.
These knobs control the volume level
of the optional built-in wireless micro-
phone system(s).
The two knobs marked “wireless mic”control the volume
of the wireless mic in use (system one or two); the red
LED’s above each knob indicate the automatic diversity
function of the receiver (flickering back and forth is nor-
mal, indicating optimum signal is being received).
ON
OFF
ST.BY
Open the lid, insert your CD and press
the play button. Adjust volume to the
desired level using the push buttons on
the CD player or the corresponding vol-
ume control on the panel (depending
on your model of CD player).
See insert page describing the features and operation of
your CD player.
Press the red button to
turn on the “talkover”
feature, which automat-
ically lowers the volume
of all other inputs
(including optional CD) when speaking
on the microphone.
Useful when making voice announcements over music
or other program material — your audience will hear
you clearly without having to manually adjust volume
controls.The volume on other inputs smoothly returns
to normal 3 seconds after you stop speaking into the
microphone. (note: The talkover feature is assigned to
optional wireless Mic 1, or the Mic 1 XLR input if no
wireless microphone is installed.)
Using Talkover
talkover
