background image

8

4)    After

 

The

 

Plastic

 

Cap

 

Is

 

Stick

 

To

 

The

 

Amp

Holding

 

Two

 

Ends

 

Of

 

The

 

Plastic

 

Caps

As

 

Shown

 

In

 

Figure 3

 ) 

And

 

Push

 

them

 

down to the same horizontal level

 ( 

As

 

Shown

 

In

 

The

 

Figure 3

).

Holding

 

both

 

ends

 

of

 

the

 

plastic

 

cap

push

 

down

 

together

 

with

 

same

 

strength

Figure 3:

6)  When

 

removing the plastic end caps

,

hold

 

two ends of the plastic cap

(

as shown in

 

the  following  figure)  and  pull

 

them  up  about  2mm  from  the  amp

.

Then  they  can  be 

taken away parallelly

.

Holding

 

both

 

ends

 

of

 

plastic

cap

 

and

 

remove

 

it

 

parallelly

5)

 

Plastic

 

cap

 

installation

 

completed

.

7

AMPLIFIERS INSTALLATION

2 )  Using attached screws to fix the amplifier to the chosen place.(As shown in figure 1)

3  )   

Each

 

plastic

 

end

 

cap

 

has

 

5

 

buckles

 

that  match  5  buckle

 

holes

 

on  the  amplifier

Hold

 

two

 

ends

 

of

 

the

 

plastic  end  cap  and

 

push  it  towards  the  amps  horizontally

.(

As 

shown in figure 2)

1 )  Choosing a flat and ventilated place to install amplifier.

          Be  sure  to  carefully  read  and  understand  the  instructions  before  attempting  to 
install the Amplifier.

1

.

Installation steps

Ho

riz

on

tal p

ush d

ire

cti

on

Ho

riz

on

tal p

ush d

ire

cti

on

Figure 1 :

Figure 2  :

Plastic End Caps Fastening Illustration

Summary of Contents for SE150.2















Reviews: