Sound Advance SpeakerTile ST2432D Series Installation Instructions Manual Download Page 2

Page  2

ST2432D Series

960.066 Rev # 1

RECOMMENDED ENVIRONMENTS

Indoor or Weather Protected Outdoor 

ACCESSORIES DATA

SOUND ADVANCE offers a backbox to allow code 
installation requirements to be met:

PBB2.0 

 — 2.0 cu. ft. backbox

Dimensions: See below. All dimensions are in inches (mm).

Weight: 4.8 lbs. (2.17 kg)

NOTE: The use of backboxes may be required by 
local or national building codes.

INSTALLATION

UNPACKING AND INSPECTION

Carefully open the shipping cartons and remove all 
contents. Inspect the SpeakerTile and accessories for dam-
age. Report damage or shortages to Sound Advance.  

Figure 1 indicates all items required for installation if 
the PBB2.0 backbox is NOT being used. See 

Figure 8 for 

details on the backbox.

CAUTION: SOUND ADVANCE loudspeakers utilize 
a fl at polystyrene material as the sound radiating 
surface. Although it is resistant to mechanical 
damage and is unaffected by environmental extremes, 
care should be observed during handling, to avoid 
punctures or other damage.

INSTALLATION PREPARATION

Determine the type of ceiling grid system (9/16” or 15/16”) 
and mounting application (fl ush or Tegular). See 

Figure 2.

9/16” AND 15/16” CEILING GRIDS: FLUSH-MOUNT 
INSTALLATION WITHOUT BACKBOX

1. If not previously done, run speaker wires or conduit 

(as per local Building Code requirements) into the se-
lected mounting location. Fasten and seal as required. 
Connect the speaker wires to the correct (+) and (–) 
SpeakerTile terminals and select the appropriate power 
tap. Insure that all connections and wiring runs are in 
compliance with required codes and regulations.

IMPORTANT: To avoid any noise or damage to the 
system when in operation be sure speaker wires or 
other objects are not in contact with the back of the 
SpeakerTile surface. To avoid damage to the front 
s u r f a c e   d u r i n g   m o u n t i n g   d o   n o t   r e m o v e   t h e 
protective cardboard cover from the Speaker Tile until it has 
been fully positioned into the ceiling.

Figure 1

Tegular

Brackets

Flush

Tegular

15

/

16

” Grid

15

/

16

” Grid

9

/

16

” Grid

9

/

16

” Grid

Figure 2

Summary of Contents for SpeakerTile ST2432D Series









Reviews: