33
Pin No.
Pin Name
I/O
Description
75
DAVN
I
Data transmit completed detect signal input from the RDS decoder (IC51) “H” active
76
KEYACK
I
Input of acknowledge signal for the key entry Acknowledge signal is input to accept function
and eject keys in the power off status On at input of “H”
77
BU-IN
I
Battery detect signal input from the SONY bus interface (IC701) and battery detect circuit
“L” is input at low voltage IC701: Used for the XR-C33R only
78
ILL IN
I
Auto dimmer control illumination line detection signal input terminal
“L” is input at dimmer detection Fixed at “L” in this set
79
TEL-ATT
I
Telephone muting signal input terminal At input of “H”, the signal is attenuated by –20 dB
Not used (open)
80
NOSESW
I
Front panel block remove/attach detection signal input terminal
“L”: front panel is attached
81
ACC IN
I
Accessory detect signal input terminal “L”: accessory on
82 to 85
NCO
O
Not used (open)
86
HSTX
I
Hardware standby input terminal “L”: hardware standby mode Reset signal input in this set
87
MD2
I
Setting terminal for the CPU operational mode (fixed at “L” in this set)
88, 89
MD1, MD0
I
Setting terminal for the CPU operational mode (fixed at “H” in this set)
90
RESET
I
System reset signal input from the reset signal generator (IC652) and reset switch (S503)
“L”: reset “L” is input for several 100 msec after power on, then it changes to “H”
91
VSS
—
Ground terminal
92
X0
I
Main system clock input terminal (3.68 MHz)
93
X1
O
Main system clock output terminal (3.68 MHz)
94
VCC
—
Power supply terminal (+5V)
95 to 99
NCO
O
Not used (open)
100
9K/10K
I
AM frequency step (9 kHz or 10 kHz) selection signal input terminal
“L”: 9 kHz, “H”: 10 kHz Not used (open)
101
NCO
O
Not used (open)
102
MTLIN
I
Auto metal detection signal input terminal “L”: auto metal Fixed at “L” in this set
103
AMSIN
I
Whether a music is present or not from CXA2509AQ (IC301) is detected at auto music sensor
“L”: music is present, “H”: music is not present
104
REEL
I
Rotation detect signal input from supply reel sensor and take-up reel sensor on the deck
mechanism
105
POS0
I
106
POS1
I
107
POS2
I
108
POS3
I
109
LM-EJ
O
Motor drive signal output to the loading/tape operation motor drive (IC361) “H” active
(For the eject direction and reverse side operation) *1
110
LM-LOD
O
Motor drive signal output to the loading/tape operation motor drive (IC361) “H” active
(For the loading direction and forward side operation) *1
111
CM-ON
O
Capstan/reel motor (M901) drive signal output terminal “H”: motor on
112
TAPEON
O
Tape system power supply on/off control signal output terminal “H”: tape on
113
N-ROUT
O
Forward/reverse direction control signal output to the CXA2509AQ (IC301)
“L”: forward direction, “H”: reverse direction
114
AMSON
O
Tape auto music sensor control signal output to the CXA2509AQ (IC301)
“L” is output to lower the gain for audio level at FF/REW mode
115
MTLON
I/O
Tape position (EJECT/FF/REW/
REV/FWD mode) detect input from
the tape operation switch on the deck
mechanism
POS0: “L”: EJECT mode, “H”: others mode
POS1: “L”: FF and FWD mode, “H”: others mode
POS2: “L”: REW mode, “H”: others mode
POS3: “L”: REV and EJECT mode, “H”: others mode
METAL control in/out terminal
At initial mode: auto/manual mode selection input of METAL function (manual at “L” input)
At manual mode: METAL on/off control signal output terminal (METAL on at “H” output)
At auto mode: input at MTLIN (pin
<z/x
)
Summary of Contents for XR-3100R
