Sony XDCAM PDW-HR1, Operation Manual, Page: 158 / 214

158
Setup Menu
C
h
ap
te
r 8
M
enu
s
Menu items in the 800s, relating to audio control (AUDIO CONTROL)
Item number Item name Settings
802 DIGITAL AUDIO MUTING IN
SHUTTLE MODE Set the audio muting conditions during shuttle playback.
off: Not muted.
on: Muted.
807 AUDIO OUTPUT PHASE Set the output timing of digital audio playback signals (HDSDI, SDI only),
with 80H as a reference position. Output timing is earlier for values
smaller than 80H and later for values greater than 80H. (80H, 128
samples = approx. 2.7 ms, 80H, 1 sample = approx. 20
μ
s)
0 (0 (HEX)) to 80 (80 (HEX)) to FF (FF (HEX)): Values can be set in this
range.
808 INTERNAL AUDIO SIGNAL
GENERATOR Select the operation of the internal audio test signal generator.
off: Prevent “SG” from being selected for sub-item AU INPUT of items
A1 INPUT to A8 INPUT on the P2 AUDIO page of the function
menu.
silnc (silence): Silent signal.
1kHz (1kHz sine): 1 kHz, –20 dB FS sine wave signal.
When you set the AU INPUT item on page P2 AUDIO of the function
menu to “SG”, the internal signal generator operates and outputs
simultaneous test signals to channels 1 to 8
(see page 58) .
820 AUDIO OUTPUT CH3/CH4 SELECT Select the signals output from the ANALOG AUDIO OUTPUT 3 and 4
connectors.
line (line out): Output the signals of the audio channels selected with
item 824 from the ANALOG AUDIO OUTPUT 3 and 4 connectors.
moni (monitor out): Output the left channel of the monitor audio (CH-1)
from the ANALOG AUDIO OUTPUT 3 connector, and output the
right channel (CH-2) from the ANALOG AUDIO OUTPUT 4
connector.
823 NON-AUDIO FLAG PB Control non-audio flags in digital audio output.
Sub-item
1 CH1/CH2 During playback (except E-E mode), set non-audio flags in digital audio
output to the following states.
on: Set to on (data is non-audio.)
auto: Set as follows.
• When data is read from disc and confirmed: Follow the data.
• When data from disc is not confirmed: Maintain current state.
2 CH3/CH4
3 CH5/CH6
4 CH7/CH8
824 ANALOG LINE OUTPUT SELECT Select the analog audio signals (tracks 1 to 8) to be assigned to audio
output channels.
Sub-item
1 CH1/CH2 tr1/2: Tracks 1 and 2 assigned to audio output channels 1 and 2.
tr3/4: Tracks 3 and 4 assigned to audio output channels 1 and 2.
tr5/6: Tracks 5 and 6 assigned to audio output channels 1 and 2.
tr7/8: Tracks 7 and 8 assigned to audio output channels 1 and 2.
2 CH3/CH4 tr1/2: Tracks 1 and 2 assigned to audio output channels 3 and 4.
tr3/4: Tracks 3 and 4 assigned to audio output channels 3 and 4.
tr5/6: Tracks 5 and 6 assigned to audio output channels 3 and 4.
tr7/8: Tracks 7 and 8 assigned to audio output channels 3 and 4.
828 SDI AUDIO OUTPUT SELECT Select the audio signals to assign to SDI audio output channels.
Sub-item
1 CH1/CH2 tr1/2: Tracks 1 and 2 assigned to audio output channels 1 and 2.
tr3/4: Tracks 3 and 4 assigned to audio output channels 1 and 2.
tr5/6: Tracks 5 and 6 assigned to audio output channels 1 and 2.
tr7/8: Tracks 7 and 8 assigned to audio output channels 1 and 2.
2 CH3/CH4 tr1/2: Tracks 1 and 2 assigned to audio output channels 3 and 4.
tr3/4: Tracks 3 and 4 assigned to audio output channels 3 and 4.
tr5/6: Tracks 5 and 6 assigned to audio output channels 3 and 4.
tr7/8: Tracks 7 and 8 assigned to audio output channels 3 and 4.