Sony XDCAM PDW-HR1, Operation Manual, Page: 58 / 214

58
Basic Function Menu Operations
Ch
apt
er 3 Prep
ar
at
ion
s
a) When V INPUT is set to “SG”, “SDI” cannot be selected for AU INPUT
on the P2 AUDIO page.
b) The settings of setup menu item 950 UP CONVERTER MODE are
reflected.
c) The settings of setup menu item 930 DOWN CONVERTER MODE are
reflected.
d) Does not appear when a GUI screen is being displayed.
P2 AUDIO page
F3: WFM Makes settings related to display of the
waveform monitor or vectorscope. (The
waveform monitor or vectorscope appear
only when the display is showing the
video monitor.)
Sub-Item
F1: MODE Display mode
OFF: Display neither.
WFM: Waveform
monitor
d)
VEC75%: 75% color
bar signal
vectorscope
d)
VEC100%: 100% color
bar signal
vectorscope
d)
F2: POSITION Display position
R.B.: Right bottom
R.T.: Right top
L.T.: Left top
L.B.: Left bottom
F3: BG Background
BLACK: Black
(opaque)
HALF: Transparent
F4: –
F5: –
F6: EXIT Exits the waveform
monitor/vectorscope
display settings sub
menu.
F4: OUT REF Selects the reference signal for the
output signals of this unit.
REF: Use the signal input to the
REF.VIDEO INPUT connector as the
output reference signal.
INPUT: Use the input video signal as the
output reference signal.
F5: SYNC Sets the sync phase of HD output
signals. While the setting value is
flashing, turn the PUSH SET knob to
adjust the sync phase of output signals
with respect to the input reference signal,
over the range ±15 µs. (The display
shows –128 to +127.)
F6: FINE Makes fine adjustment to the sync phase
of HD output signals. While the setting
value is flashing, turn the PUSH SET
knob to adjust the sync phase of output
signals with respect to the input
reference signal, over the range ±200 ns.
(The display shows 0 to 1023.)
Item Setting
Item Setting
F1: AU INPUT Selects the audio input signal to assign
to audio channels 1 to 8.
SDI: Audio signal embedded into SDI
signal
ANALOG1: Analog 1 audio signal
SG: Test signal from internal signal
generator
i.LINK: i.LINK signal (when the PDBK-
202 option board is installed)
DVB-ASI: DVB-ASI signal (when the
PDBK-202 option board is installed)
Sub-item
F1: A1
INPUT (A5
INPUT) Input signal of audio
channel 1 (5)
F2: A2
INPUT (A6
INPUT) Input signal of audio
channel 2 (6)
F3: A3
INPUT (A7
INPUT) Input signal of audio
channel 3 (7)
F4: A4
INPUT (A8
INPUT) Input signal of audio
channel 4 (8)
F5: A5-A8
(A1-A4) Switches to the sub menu
for setting channels 5 to 8
(1 to 4).
F6: EXIT Exit the audio input signal
selection sub-menu.
F2: REC VOL Sets the recording audio level of audio
channels 5 to 8.
a)
The recording audio level can be
adjusted within the range from –200 to
+200 (–
∞
to +12 dB) by turning the PUSH
SET knob.
Sub-item
F1: A5 VOL Recording audio level of
audio channel 5
F2: A6 VOL Recording audio level of
audio channel 6
F3: A7 VOL Recording audio level of
audio channel 7
F4: A8 VOL Recording audio level of
audio channel 8
F5: –
F6: EXIT Exit the recording audio
level setting sub-menu.