Sony XBR-75X945C Service Manual Download Page 101

Page: 101 / 209

XBR-65X930C, 75X940C, 945C

101

DISASSEMBLY

1-2-44. GASKET (BMF)

1-2. XBR-75X940C/945C

GASKET (BMF)

Stick GASKET inside the guide line.

To stick the GASKET firmly,

Press the gasket until compression completely.

(0.5-1.0kgf)

Guide line

*No indication of direction

Caution:

Please aim at the center of square land.

Assy the gaskets just before B board panel installation.

NOTE:

When you replace a BMFW board, it is necessary to stick five

new GASKET on a new BMFW board.

GASKET (BMF): 4-566-117-01

But in below cases, GASKET is not necessary.

GASKET is soldered onto the surface of the board

In case below number is printed on the surface of the B-board

"1-894-595-12

or 22“

(Please note that this is not the P/N of mounted board)

Summary of Contents for XBR-75X945C


















































































































































































































Search results

Summary of Contents for XBR-75X945C

Reviews:

Brands by name

Popular brands

Sony XBR-75X945C, Service Manual

Search results

Summary of Contents for XBR-75X945C

Reviews:

Brands by name

Popular brands